1. Welcome to 4Runners.com!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all 4Runner discussion topics
    • Transfer over your build thread from a different forum to this one
    • Communicate privately with other 4Runner owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

SR5 Stock Height Measurements?

Discussion in '5th Gen 4Runners (2010+)' started by brochacho, Aug 16, 2016.

  1. Aug 16, 2016 at 8:35 AM
    #1
    brochacho

    brochacho [OP] New Member

    Joined:
    Jun 20, 2016
    Member:
    #2179
    Messages:
    467
    Gender:
    Male
    PNW
    Vehicle:
    2018 Sequoia TRD Sport
    I'm an idiot and forgot to measure before my lift. Does anybody have their stock height measurement with stock SR5 wheels? I don't really care about the method used (hub to fender or ground to fender) and I know every truck is different but I'm hoping it should at least be in the ballpark. Thanks!
     
    Strandskov likes this.
  2. Aug 16, 2016 at 1:39 PM
    #2
    Bob

    Bob Member Staff Member

    Joined:
    Apr 3, 2014
    Member:
    #1
    Messages:
    1,807
    First Name:
    Bob
    SoCal
    Sub'd so we can sticky it
     
  3. Aug 17, 2016 at 1:34 PM
    #3
    MaliciousClout

    MaliciousClout New Member

    Joined:
    Aug 16, 2016
    Member:
    #2477
    Messages:
    9
    Gender:
    Male
    First Name:
    Ian
    Vehicle:
    2015 TEP SuperWhite
    TRD garnish/PlastiDipped Valances/ N-Fab Steps/285-70-17/3 Inch ToyTec Lift/1.25 Spidertrax Spacers/Total LED Swap/6000K HID
    All T4R's heights vary from the factory. I'm interested though in seeing the differences albeit slight I'm sure. Sub'd as well.
     
    Strandskov likes this.
  4. Aug 18, 2016 at 3:10 PM
    #4
    j cat

    j cat New Member

    Joined:
    Jun 28, 2016
    Member:
    #2223
    Messages:
    537
    massachusetts
    spacer lift front 1inch
    on my 2016 1K miles front ground to bottom of the fender @ center cap. 34-5/8inch rear 36-5/8 inch..
    I just adjusted the front tie rod pass side today added a little toe in .. had zero toe wandered too much. good now.
     
    Strandskov and brochacho [OP] like this.
  5. Mar 16, 2019 at 3:52 PM
    #5
    P226Navy

    P226Navy 2016 T4R

    Joined:
    Mar 11, 2018
    Member:
    #5642
    Messages:
    320
    Gender:
    Male
    First Name:
    Vee
    South San Francisco
    Vehicle:
    2016 Toyota 4Runner
    Center cap to fender line is the most accurate measurement.
     
    Strandskov likes this.
  6. Mar 16, 2019 at 7:05 PM
    #6
    JohnD

    JohnD New Member

    Joined:
    Dec 30, 2018
    Member:
    #8261
    Messages:
    15
    Gender:
    Male
    My 2018 SR5 was 19.6” front driver, 20” front pass, 21.5” rear driver, 22.1 rear pass. Center of cap to fender lip.
     
  7. Mar 17, 2019 at 7:08 AM
    #7
    j cat

    j cat New Member

    Joined:
    Jun 28, 2016
    Member:
    #2223
    Messages:
    537
    massachusetts
    spacer lift front 1inch
    yes you are correct for the accurate measurement of vehicle height .. but I did the spring spacer lift and I was not all that concerned about the exact height , was only interested in the amount of lift it/spacer created.
    the vehicle has now 25K miles on it and all my tires look exactly the same .. also the nose dive is still gone .. spring spacers holding up and also on the cheap .. cost $20 total..
     
    P226Navy likes this.
  8. Mar 17, 2019 at 8:00 AM
    #8
    P226Navy

    P226Navy 2016 T4R

    Joined:
    Mar 11, 2018
    Member:
    #5642
    Messages:
    320
    Gender:
    Male
    First Name:
    Vee
    South San Francisco
    Vehicle:
    2016 Toyota 4Runner
    What spacers are they?
     
  9. Mar 17, 2019 at 2:04 PM
    #9
    j cat

    j cat New Member

    Joined:
    Jun 28, 2016
    Member:
    #2223
    Messages:
    537
    massachusetts
    spacer lift front 1inch
    the coil springs are different . the driver side is a stronger spring bigger so the gas tank will not cause the vehicle to droop on the driver side the pass side has a smaller coil spring spaces closer..

    I fabricated a 11/2 inch screw in spacer into the lower portion of the driver side spring. had to cut it and file the contour..

    ON the pass side I installed 2 1inch spacers on the lower portion of the coil .. one in front the other in rear of the pass coil .. had to fabricate the spacer so it would screw in and not whack the shock tube..

    perhaps when my front shocks need replacing and I have the tools I will install the bilstein adjustable shocks and use a strut spacer to stiffen the springs .. I am no toyota lift expert but so far I am doing good on the dive issue that many did not like..
     
    P226Navy likes this.

Products Discussed in

To Top