1. Welcome to 4Runners.com!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all 4Runner discussion topics
    • Transfer over your build thread from a different forum to this one
    • Communicate privately with other 4Runner owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

SPC UCA failures

Discussion in '5th Gen 4Runners (2010-2024)' started by 2021venture, May 4, 2023.

  1. May 4, 2023 at 6:40 AM
    #1
    2021venture

    2021venture [OP] New Member

    Joined:
    Jan 15, 2023
    Member:
    #30658
    Messages:
    855
    Gender:
    Male
    First Name:
    Todd
    Vehicle:
    2021 Venture
    Elka 2.5, Apache Offroad UCA, durobumps, RCI full skids, RSG sliders, 10 lb Powertank, Maxtrax, Hi lift jack, Westscott Designs modular roof rack and ladder, ARB rear diff breather relocate, ECGS bushing upgrade, c4 low profile bumper, Baja designs S8 lightbar, warn evo winch, factor 55 ultrahook, 80% off-road rear bumper, 4.56 regear
    I have SPC UCA and went with them because of adjustability. The alignment went smooth and truck rides nice meeting my expectations. I have read reports of them failing which initially had me leaning towards JBA. Anyone have experience with SPC failing or what to watch out for? I currently grease the driveshafts every 5k oil changes and will grease them also.
     
    kolter45 likes this.
  2. May 4, 2023 at 6:48 AM
    #2
    OverRunner

    OverRunner rebmeM weN

    Joined:
    May 2, 2021
    Member:
    #21242
    Messages:
    297
    Gender:
    Male
    First Name:
    Jared
    Denton, TX
    Vehicle:
    ‘21 ORP w/KDSS
    Disclaimer: Have not used these, and don’t know anyone personally who does. What I share is the fruits of my research (a several month-long comparison of over 40 UCA options).

    They seem to have a decent warranty if you cover all your bases at purchase time, but I have read stories of warranties not being honored because of a lack of registration/receipt.

    I’ve also read that if you off-road it hard, the control arm can snap where the arm meets the bushing. I don’t remember reading about any of them failing prematurely from strictly on-road use.

    They seem to be the perfect option for the light-duty crowd given their weight, cost, adjustability, etc.
     
    2021venture[OP] likes this.
  3. May 4, 2023 at 7:47 AM
    #3
    whippersnapper02

    whippersnapper02 New Member

    Joined:
    Feb 27, 2019
    Member:
    #8982
    Messages:
    3,027
    Gender:
    Male
    First Name:
    Christian
    Vehicle:
    2019 4Runner TRD Offroad Premium
    I have them on the shelf for my Runner. I don’t think they have had any recent issues with them and I didn’t have issues with them when I ran them on my Tacoma.
     
    MyWyfsRnnr likes this.
  4. May 4, 2023 at 7:48 AM
    #4
    djwantke

    djwantke New Member

    Joined:
    Jan 31, 2021
    Member:
    #19487
    Messages:
    3,535
    Gender:
    Male
    Maple Ridge, British Columbia
    Vehicle:
    2016 4Runner Trail Premium
    Bought brand new 2016 After May 2021: -Approx 3" lift/level: Bilstein 5100's, OME 2884 590lb 3" front lift springs, SPC UCA's, ICON 158506 2" lift rear coils, diff drop -Mickey Thompson Baja ATZ LT285/70R17 Load E -Mickey Thompson Sidebiter ll 17x9, 0 offset, 5 backspace -Pro Comp black spline lugs ^installed by 4WheelParts^ -New brakes and rotors by brake shop -4-piece ARB skid kit -Smittybilt 2" nerf steps -MBRP black exhaust tip, chopped OEM -Drivers side OEM FJ oh shit handle -All blacked out emblems -Blacked out roof rails -4x WeatherTech window rain guards -OEM custom rear mud flap deletes -KICK BACK MUD FLAPS 12" WIDE - BLACK TOP AND BLACK WEIGHT -FRAM EXTRA GUARD CA10835 engine air filter -1797 LED tricolor fog bulbs Yellow 3000K White 6000K Blue 15000K 28W 4000LM -Armour paint lower rear bumper -Front bumper high stage high clearance cut -Fenders cut straight across, pink reservoir sprayed black -4Runner Lifestyle sequential fog fangs -4Runner Lifestyle smoked taillight decals -Pedal Commander -Rear passenger cargo mounted 120v truck tire pump -4x Spidertrax 1.25" black aluminum wheel spacers -Yota Twins Paracord Hatch Strap sand camo -Teton Workshop hard anodized matte black aluminum shift knob -Ditch flood lights 4 LED 20w 1400lm w/ OEM hood mounts on OEM style dash switch -Backup flood lights under bumper 6 LED 18w 1500lm on OEM style dash switch -Body Mount Chop; cut, weld, paint -Fender mount chop, re-weld, paint -Fender Liner cut behind wheel (I cut liner in front of wheel clean off at top of viper cut) -Wheel well firewall hammering, painting ^done by Arc One Industries^ -valance cap trim -Agency6 Black Shackle Block 2" US Certified 6061 T6 CNC machined aluminum -DRT fab universal hitch skid -ACDelco inner tie rods, outer tie rods, bellows -Full Dr. KDSS switch kit -March 31 Behind grille 13-1/4" 32 LED light bar + wide-angle, eagle-eye lens 6000lm on OEM style dash switch -RAA Powder coated steel roof rack cargo basket, 1" side rails, 64" x 39" x 6", 250lb limit -roof gas can, water can, shovel -PEAKTOW PTT0063 Hitch Mount Cargo Carrier 51-1/2 x 17-1/2 x 4 inches 500 lbs. Capacity (trips only) -July/2023: purchased first needed SPC balljoint replacement kit - newly released, upgraded non-zerk sealed joints 25002 -July 15/2023: The Original Universal EZ Flares, 1". All four corners -Dec. 2023: removed bumper cover and crash bar, drilled frame, installed Apex Overland KDSS Recovery Points -Jan. 2024: SPC balljoint replacement kit - upgraded non-zerk sealed joint design 25002 -Feb. 3/ 2024: 4x KC Wire Hiders, for roof rack lighting Feb. 13/2024: New ditch lights, on new Rago Fabrication Extension brackets. 3inch Quad Row Amber Pods from LED-Club. 32W 3200Lm 16-LED Spot Beam. Replacing 3inch EVERGEAR clear lens ditch light pods w/ yellow lamix-x In progress: 4th, 5th, and 6th set of off road lights Electrical components and wiring purchased, not started -roof rack scene lighting - EVERGEAR ea. 1,350 lumens, 30w, 3-¾" round floods. Custom, side mounted w/ galvanized flat bar And -roof rack upper ditch lights - 3inch Quad Row Amber Pods from LED-Club. 32W 3200Lm 16-LED Spot Beam. Bar clamp mounted to front corners And -roof rack reverse amber pods / secondary hazard lights. 20W 2000Lm 2-LED Spot Beam. Bar clamp mounted to rear side And -roof rack F1 smoked chase light w/ lighting effects. Custom bolted to rear side -POR15 rust proofing line-up, 3-step process PAUSED until 70⁰ weather Bought, in the garage queue: -BlueFire 6-Circuit Fuse Block with LED Indicator & Protection Cover -Blue Sea Systems 100A Circuit Breaker w/ reset lever -Rust prevention •New can POR15, 2x Black Fluid Film, long spray nozzle attachments, 2x PB Surface Shield, 1x Chainwax •partially used POR15 Degreaser, Metal Prep Wanted - PerryParts or Wheelers bump stops, self fabricated limb risers (seasonal, removable), 1" body lift, powder coated center winch bumper w/ large bar (got no tss), rear steel bumper w/ tire carrier for an LT285 Kumho on steely, sliders, bolt on cat shields
    I've ran SPC UCAs for 2 years, they've been great for exactly what OverRunner outlined.
    I have 3/2 Bilstein suspension lift, upgraded springs, 17x9 0/4.5, LT285/70R17 E, little bit of added weight. SPC arms and ball joints and bushings held up with all that.
    What often goes on people is the ball joints and ball joint boots. My boots never ripped, but I blew out one grease seal before from way over pumping the grease gun from inexperience.
    Recently replaced tie rods, and my shop said you got 6 months left on those SPC ball joints. I bought a replacement kit from Lordco $200-300 gunna do it myself
     
    MyWyfsRnnr and OverRunner like this.
  5. May 4, 2023 at 7:49 AM
    #5
    djwantke

    djwantke New Member

    Joined:
    Jan 31, 2021
    Member:
    #19487
    Messages:
    3,535
    Gender:
    Male
    Maple Ridge, British Columbia
    Vehicle:
    2016 4Runner Trail Premium
    Bought brand new 2016 After May 2021: -Approx 3" lift/level: Bilstein 5100's, OME 2884 590lb 3" front lift springs, SPC UCA's, ICON 158506 2" lift rear coils, diff drop -Mickey Thompson Baja ATZ LT285/70R17 Load E -Mickey Thompson Sidebiter ll 17x9, 0 offset, 5 backspace -Pro Comp black spline lugs ^installed by 4WheelParts^ -New brakes and rotors by brake shop -4-piece ARB skid kit -Smittybilt 2" nerf steps -MBRP black exhaust tip, chopped OEM -Drivers side OEM FJ oh shit handle -All blacked out emblems -Blacked out roof rails -4x WeatherTech window rain guards -OEM custom rear mud flap deletes -KICK BACK MUD FLAPS 12" WIDE - BLACK TOP AND BLACK WEIGHT -FRAM EXTRA GUARD CA10835 engine air filter -1797 LED tricolor fog bulbs Yellow 3000K White 6000K Blue 15000K 28W 4000LM -Armour paint lower rear bumper -Front bumper high stage high clearance cut -Fenders cut straight across, pink reservoir sprayed black -4Runner Lifestyle sequential fog fangs -4Runner Lifestyle smoked taillight decals -Pedal Commander -Rear passenger cargo mounted 120v truck tire pump -4x Spidertrax 1.25" black aluminum wheel spacers -Yota Twins Paracord Hatch Strap sand camo -Teton Workshop hard anodized matte black aluminum shift knob -Ditch flood lights 4 LED 20w 1400lm w/ OEM hood mounts on OEM style dash switch -Backup flood lights under bumper 6 LED 18w 1500lm on OEM style dash switch -Body Mount Chop; cut, weld, paint -Fender mount chop, re-weld, paint -Fender Liner cut behind wheel (I cut liner in front of wheel clean off at top of viper cut) -Wheel well firewall hammering, painting ^done by Arc One Industries^ -valance cap trim -Agency6 Black Shackle Block 2" US Certified 6061 T6 CNC machined aluminum -DRT fab universal hitch skid -ACDelco inner tie rods, outer tie rods, bellows -Full Dr. KDSS switch kit -March 31 Behind grille 13-1/4" 32 LED light bar + wide-angle, eagle-eye lens 6000lm on OEM style dash switch -RAA Powder coated steel roof rack cargo basket, 1" side rails, 64" x 39" x 6", 250lb limit -roof gas can, water can, shovel -PEAKTOW PTT0063 Hitch Mount Cargo Carrier 51-1/2 x 17-1/2 x 4 inches 500 lbs. Capacity (trips only) -July/2023: purchased first needed SPC balljoint replacement kit - newly released, upgraded non-zerk sealed joints 25002 -July 15/2023: The Original Universal EZ Flares, 1". All four corners -Dec. 2023: removed bumper cover and crash bar, drilled frame, installed Apex Overland KDSS Recovery Points -Jan. 2024: SPC balljoint replacement kit - upgraded non-zerk sealed joint design 25002 -Feb. 3/ 2024: 4x KC Wire Hiders, for roof rack lighting Feb. 13/2024: New ditch lights, on new Rago Fabrication Extension brackets. 3inch Quad Row Amber Pods from LED-Club. 32W 3200Lm 16-LED Spot Beam. Replacing 3inch EVERGEAR clear lens ditch light pods w/ yellow lamix-x In progress: 4th, 5th, and 6th set of off road lights Electrical components and wiring purchased, not started -roof rack scene lighting - EVERGEAR ea. 1,350 lumens, 30w, 3-¾" round floods. Custom, side mounted w/ galvanized flat bar And -roof rack upper ditch lights - 3inch Quad Row Amber Pods from LED-Club. 32W 3200Lm 16-LED Spot Beam. Bar clamp mounted to front corners And -roof rack reverse amber pods / secondary hazard lights. 20W 2000Lm 2-LED Spot Beam. Bar clamp mounted to rear side And -roof rack F1 smoked chase light w/ lighting effects. Custom bolted to rear side -POR15 rust proofing line-up, 3-step process PAUSED until 70⁰ weather Bought, in the garage queue: -BlueFire 6-Circuit Fuse Block with LED Indicator & Protection Cover -Blue Sea Systems 100A Circuit Breaker w/ reset lever -Rust prevention •New can POR15, 2x Black Fluid Film, long spray nozzle attachments, 2x PB Surface Shield, 1x Chainwax •partially used POR15 Degreaser, Metal Prep Wanted - PerryParts or Wheelers bump stops, self fabricated limb risers (seasonal, removable), 1" body lift, powder coated center winch bumper w/ large bar (got no tss), rear steel bumper w/ tire carrier for an LT285 Kumho on steely, sliders, bolt on cat shields
    They had issues during covid because of manufacturer changes due to supply chain, and seem to have now worked out the deficiencies with new stock. From what I gather
     
  6. May 4, 2023 at 12:50 PM
    #6
    blksubykid

    blksubykid New Member

    Joined:
    Oct 1, 2021
    Member:
    #23606
    Messages:
    176
    Gender:
    Male
    4 years and over 30k miles...no issues. I just replace the ball joints as preventative maintenance tho
     
  7. May 5, 2023 at 10:36 AM
    #7
    4runwildintoparadise

    4runwildintoparadise New Member

    Joined:
    Dec 29, 2021
    Member:
    #24861
    Messages:
    13
    Gender:
    Female
    Vancouver, BC
    Vehicle:
    2021 4Runner TRD Off-road
    Suspension: Dobinsons MRR Modular Panels: Rago Fabrication Tires: Falken Wildpeaks 275/70/17
    Mine were in a batch that was received and failed. When you grab the UCA and test it for any movement or play, it would jolt and move around as well. Ball joints would also spew grease every time i started to drive or take it off on a dirt road. This was even installed by a professional company for more comfortability of having it done properly. Multiple vehicles that had them installed after on the same batch had the same problem.

    I ended getting JBA UCA's and yes they aren't like the SPC's but they are similar and I have had nothing but fun with these ones. No problems up to date and I go out just about every weekend to get my fix, so my 4Runner is well used when it comes to it's suspension.
     
    OverRunner likes this.
  8. May 5, 2023 at 11:46 AM
    #8
    kolter45

    kolter45 Inferno Pro & 4.0 Tacoma

    Joined:
    May 7, 2022
    Member:
    #26975
    Messages:
    702
    Gender:
    Male
    Denver
    Vehicle:
    Inferno Pro & BRM Sport
    My SPCs on my taco were the bad bushings from 2019. It was like pulling teeth to get them to confess & send me new ones. Customer service blows & if you’re assigned “Todd” … good luck. He’s very difficult to work with. I wish I bought JBAs
     
  9. May 5, 2023 at 11:48 AM
    #9
    4runwildintoparadise

    4runwildintoparadise New Member

    Joined:
    Dec 29, 2021
    Member:
    #24861
    Messages:
    13
    Gender:
    Female
    Vancouver, BC
    Vehicle:
    2021 4Runner TRD Off-road
    Suspension: Dobinsons MRR Modular Panels: Rago Fabrication Tires: Falken Wildpeaks 275/70/17
    What did you end up going with?
     
    kolter45[QUOTED] likes this.
  10. May 5, 2023 at 5:37 PM
    #10
    kolter45

    kolter45 Inferno Pro & 4.0 Tacoma

    Joined:
    May 7, 2022
    Member:
    #26975
    Messages:
    702
    Gender:
    Male
    Denver
    Vehicle:
    Inferno Pro & BRM Sport
    I have the replacement bushing they sent me. Pain in the ass to get new bushing into them. They’re fine now but not a fun experience
     
  11. Jul 8, 2023 at 8:55 AM
    #11
    Heckler44

    Heckler44 New Member

    Joined:
    Dec 13, 2021
    Member:
    #24630
    Messages:
    23
    First Name:
    Sean
    Vehicle:
    2021 Venture Silver
    My SPCs started getting bad at under 5k miles. Installed at a professional shop in Commerce City, CO. Took my 4R in for its first tire rotation and they pointed out that the SPCs were about shot. I worked with SPC, $800 later had a complete new set. IMO I don't think I should have had to pay warranty replacement costs for something they knew was an issue. Complete new set of SPCs on now. I will give them a chance but lost a lot of faith in them. I had SPCs on my Taco for over 8 years with no issues what so ever.
     
    kolter45 and kmeeg like this.
  12. Jul 8, 2023 at 9:01 AM
    #12
    kmeeg

    kmeeg New Member

    Joined:
    Apr 18, 2018
    Member:
    #5853
    Messages:
    5,264
    Gender:
    Male
    Thanks for sharing this to save others time and money. I will keep them out of my list for my next project.
     
    raimieb and kolter45[QUOTED] like this.
  13. Jul 8, 2023 at 11:51 AM
    #13
    Rob41

    Rob41 Veteran

    Joined:
    Jun 23, 2023
    Member:
    #33566
    Messages:
    946
    Gender:
    Male
    First Name:
    Rob
    Northern Michigan
    Vehicle:
    2023 Supercharged 4Runner TRD
    Magnuson Supercharger, CSF Performance Radiator, Eibach Pro-Truck Series 2R suspension, SCS Ray10 Bronze Wheels, Pedal Monster, TRD Pro Grill, TRD Pro Roof Rack
    I read about too many bad experiences with the very common SPC UCA's. That's why I chose the tried and true Dobinson's that have 3 degrees of castor correction built in. You have to have at least 1.5 inches of lift to be able to use these but they are robust and reliable.

    Here is what they have to say:
    • Complete kit for both left and right hand side, includes new ball joints (Pressed), OE style rubber frame bushings (installed), and washers
    • Has 3 degrees of caster built in, no adjustability or settings required
    • Made from HSLA (High Strength Low Alloy) Steel, 5mm (0.2") wall thickness, and powder coated black
    • Works for any lift height of 1.5" or more. Any height less than that, a proper wheel alignment may not be able to be achieved
    • Uses replaceable Japanese-made Sankei 555 ball joints, fully sealed for maintenance free life
     
  14. Jul 8, 2023 at 12:31 PM
    #14
    kmeeg

    kmeeg New Member

    Joined:
    Apr 18, 2018
    Member:
    #5853
    Messages:
    5,264
    Gender:
    Male
    Please share if anyone knows lifted vehicle friendly UCAs that does not require maintenance like the Toyota UCA.

    If there's any long travel friendly no maintenance required ULA and LCA available it would be even better for me to take a look. Haven't decided about long travel yet due to high maintenance.
     
  15. Jul 8, 2023 at 4:54 PM
    #15
    nova

    nova New Member

    Joined:
    Aug 26, 2022
    Member:
    #28359
    Messages:
    563
    Gender:
    Male
    First Name:
    mike
    Prescott Valley - Arizona
    Vehicle:
    slightly modified LE
    4.88, Air lockers, 35 Toyo MTs, C4 body armor, +2 LT, etc
    Long travel friendly? If you’re going Long Travel you’ll be buying after market upper and lower control arms. Not SPC.

    Also, any Long Travel I’ve seen will require some maintenance (uni-ball vs ball Balljoints).

    I think it’s worth it if your activities benefit from Long Travel. It is an investment as you can no longer use any OE front suspension components.

    Good luck!
     
    kolter45 and kmeeg like this.
  16. Jul 9, 2023 at 4:44 AM
    #16
    2021venture

    2021venture [OP] New Member

    Joined:
    Jan 15, 2023
    Member:
    #30658
    Messages:
    855
    Gender:
    Male
    First Name:
    Todd
    Vehicle:
    2021 Venture
    Elka 2.5, Apache Offroad UCA, durobumps, RCI full skids, RSG sliders, 10 lb Powertank, Maxtrax, Hi lift jack, Westscott Designs modular roof rack and ladder, ARB rear diff breather relocate, ECGS bushing upgrade, c4 low profile bumper, Baja designs S8 lightbar, warn evo winch, factor 55 ultrahook, 80% off-road rear bumper, 4.56 regear
    What I find odd is many well respected off road shops recommend SPC. I was not going the low cost route but trying to build a quality setup. I had SPC recommended with Elka's. Any guesses why shops are recommending SPC? I do agree Dobinson's look like very solid UCA. For a stronger off road UCA there are better than SPC but the adjustability of SPC is nice for easy alignment.
     
    travelinscout likes this.
  17. Jul 9, 2023 at 5:02 PM
    #17
    Slopemaster

    Slopemaster Slope Survivalist

    Joined:
    Mar 20, 2021
    Member:
    #20442
    Messages:
    3,090
    Gender:
    Male
    Idaho
    Vehicle:
    2018 SR5
    265-70-17 Ridge Grapplers, TRD Pro rims, 3M precut bra, N-Fab nerf/steps
    I had a local 4x4 shop give me a quote on a Bilstein upgrade. They also suggested SPC UCA’s.

    Ultimately, I decided to forgo the suspension/lift and leave it stock.
     
    djb1 likes this.
  18. Jul 10, 2023 at 12:28 PM
    #18
    djwantke

    djwantke New Member

    Joined:
    Jan 31, 2021
    Member:
    #19487
    Messages:
    3,535
    Gender:
    Male
    Maple Ridge, British Columbia
    Vehicle:
    2016 4Runner Trail Premium
    Bought brand new 2016 After May 2021: -Approx 3" lift/level: Bilstein 5100's, OME 2884 590lb 3" front lift springs, SPC UCA's, ICON 158506 2" lift rear coils, diff drop -Mickey Thompson Baja ATZ LT285/70R17 Load E -Mickey Thompson Sidebiter ll 17x9, 0 offset, 5 backspace -Pro Comp black spline lugs ^installed by 4WheelParts^ -New brakes and rotors by brake shop -4-piece ARB skid kit -Smittybilt 2" nerf steps -MBRP black exhaust tip, chopped OEM -Drivers side OEM FJ oh shit handle -All blacked out emblems -Blacked out roof rails -4x WeatherTech window rain guards -OEM custom rear mud flap deletes -KICK BACK MUD FLAPS 12" WIDE - BLACK TOP AND BLACK WEIGHT -FRAM EXTRA GUARD CA10835 engine air filter -1797 LED tricolor fog bulbs Yellow 3000K White 6000K Blue 15000K 28W 4000LM -Armour paint lower rear bumper -Front bumper high stage high clearance cut -Fenders cut straight across, pink reservoir sprayed black -4Runner Lifestyle sequential fog fangs -4Runner Lifestyle smoked taillight decals -Pedal Commander -Rear passenger cargo mounted 120v truck tire pump -4x Spidertrax 1.25" black aluminum wheel spacers -Yota Twins Paracord Hatch Strap sand camo -Teton Workshop hard anodized matte black aluminum shift knob -Ditch flood lights 4 LED 20w 1400lm w/ OEM hood mounts on OEM style dash switch -Backup flood lights under bumper 6 LED 18w 1500lm on OEM style dash switch -Body Mount Chop; cut, weld, paint -Fender mount chop, re-weld, paint -Fender Liner cut behind wheel (I cut liner in front of wheel clean off at top of viper cut) -Wheel well firewall hammering, painting ^done by Arc One Industries^ -valance cap trim -Agency6 Black Shackle Block 2" US Certified 6061 T6 CNC machined aluminum -DRT fab universal hitch skid -ACDelco inner tie rods, outer tie rods, bellows -Full Dr. KDSS switch kit -March 31 Behind grille 13-1/4" 32 LED light bar + wide-angle, eagle-eye lens 6000lm on OEM style dash switch -RAA Powder coated steel roof rack cargo basket, 1" side rails, 64" x 39" x 6", 250lb limit -roof gas can, water can, shovel -PEAKTOW PTT0063 Hitch Mount Cargo Carrier 51-1/2 x 17-1/2 x 4 inches 500 lbs. Capacity (trips only) -July/2023: purchased first needed SPC balljoint replacement kit - newly released, upgraded non-zerk sealed joints 25002 -July 15/2023: The Original Universal EZ Flares, 1". All four corners -Dec. 2023: removed bumper cover and crash bar, drilled frame, installed Apex Overland KDSS Recovery Points -Jan. 2024: SPC balljoint replacement kit - upgraded non-zerk sealed joint design 25002 -Feb. 3/ 2024: 4x KC Wire Hiders, for roof rack lighting Feb. 13/2024: New ditch lights, on new Rago Fabrication Extension brackets. 3inch Quad Row Amber Pods from LED-Club. 32W 3200Lm 16-LED Spot Beam. Replacing 3inch EVERGEAR clear lens ditch light pods w/ yellow lamix-x In progress: 4th, 5th, and 6th set of off road lights Electrical components and wiring purchased, not started -roof rack scene lighting - EVERGEAR ea. 1,350 lumens, 30w, 3-¾" round floods. Custom, side mounted w/ galvanized flat bar And -roof rack upper ditch lights - 3inch Quad Row Amber Pods from LED-Club. 32W 3200Lm 16-LED Spot Beam. Bar clamp mounted to front corners And -roof rack reverse amber pods / secondary hazard lights. 20W 2000Lm 2-LED Spot Beam. Bar clamp mounted to rear side And -roof rack F1 smoked chase light w/ lighting effects. Custom bolted to rear side -POR15 rust proofing line-up, 3-step process PAUSED until 70⁰ weather Bought, in the garage queue: -BlueFire 6-Circuit Fuse Block with LED Indicator & Protection Cover -Blue Sea Systems 100A Circuit Breaker w/ reset lever -Rust prevention •New can POR15, 2x Black Fluid Film, long spray nozzle attachments, 2x PB Surface Shield, 1x Chainwax •partially used POR15 Degreaser, Metal Prep Wanted - PerryParts or Wheelers bump stops, self fabricated limb risers (seasonal, removable), 1" body lift, powder coated center winch bumper w/ large bar (got no tss), rear steel bumper w/ tire carrier for an LT285 Kumho on steely, sliders, bolt on cat shields
    @2021venture
    @Slopemaster
    My two cents; Bilstein's, SPC's, and upgraded springs were my local shops #1 recommendation for my budget and driving. It's a highly tested 4Runner setup for them in BC, and SPC's in particular have been solid for years. It's really only the covid manufacturing material changes that are a blemish on their record. They're still known for good quality and longevity, hence widely recommended.

    That being said
    2-3 years out of my covid SPC's and the balljoints have been given 6 months to live by my local guys. I already bought the SPC balljoint replacement kit on discount from Lordco. Right now boots leak a little grease I have to wipe each week.

    And I've posted on here for help couple times now - there's a grinding/rubbing noise sometimes when I turn hard left or right going quick up an incline. Not getting any rubbing evidence elsewhere. Could this be the ball in socket metal on metal?
     
  19. Jul 30, 2023 at 5:40 PM
    #19
    djwantke

    djwantke New Member

    Joined:
    Jan 31, 2021
    Member:
    #19487
    Messages:
    3,535
    Gender:
    Male
    Maple Ridge, British Columbia
    Vehicle:
    2016 4Runner Trail Premium
    Bought brand new 2016 After May 2021: -Approx 3" lift/level: Bilstein 5100's, OME 2884 590lb 3" front lift springs, SPC UCA's, ICON 158506 2" lift rear coils, diff drop -Mickey Thompson Baja ATZ LT285/70R17 Load E -Mickey Thompson Sidebiter ll 17x9, 0 offset, 5 backspace -Pro Comp black spline lugs ^installed by 4WheelParts^ -New brakes and rotors by brake shop -4-piece ARB skid kit -Smittybilt 2" nerf steps -MBRP black exhaust tip, chopped OEM -Drivers side OEM FJ oh shit handle -All blacked out emblems -Blacked out roof rails -4x WeatherTech window rain guards -OEM custom rear mud flap deletes -KICK BACK MUD FLAPS 12" WIDE - BLACK TOP AND BLACK WEIGHT -FRAM EXTRA GUARD CA10835 engine air filter -1797 LED tricolor fog bulbs Yellow 3000K White 6000K Blue 15000K 28W 4000LM -Armour paint lower rear bumper -Front bumper high stage high clearance cut -Fenders cut straight across, pink reservoir sprayed black -4Runner Lifestyle sequential fog fangs -4Runner Lifestyle smoked taillight decals -Pedal Commander -Rear passenger cargo mounted 120v truck tire pump -4x Spidertrax 1.25" black aluminum wheel spacers -Yota Twins Paracord Hatch Strap sand camo -Teton Workshop hard anodized matte black aluminum shift knob -Ditch flood lights 4 LED 20w 1400lm w/ OEM hood mounts on OEM style dash switch -Backup flood lights under bumper 6 LED 18w 1500lm on OEM style dash switch -Body Mount Chop; cut, weld, paint -Fender mount chop, re-weld, paint -Fender Liner cut behind wheel (I cut liner in front of wheel clean off at top of viper cut) -Wheel well firewall hammering, painting ^done by Arc One Industries^ -valance cap trim -Agency6 Black Shackle Block 2" US Certified 6061 T6 CNC machined aluminum -DRT fab universal hitch skid -ACDelco inner tie rods, outer tie rods, bellows -Full Dr. KDSS switch kit -March 31 Behind grille 13-1/4" 32 LED light bar + wide-angle, eagle-eye lens 6000lm on OEM style dash switch -RAA Powder coated steel roof rack cargo basket, 1" side rails, 64" x 39" x 6", 250lb limit -roof gas can, water can, shovel -PEAKTOW PTT0063 Hitch Mount Cargo Carrier 51-1/2 x 17-1/2 x 4 inches 500 lbs. Capacity (trips only) -July/2023: purchased first needed SPC balljoint replacement kit - newly released, upgraded non-zerk sealed joints 25002 -July 15/2023: The Original Universal EZ Flares, 1". All four corners -Dec. 2023: removed bumper cover and crash bar, drilled frame, installed Apex Overland KDSS Recovery Points -Jan. 2024: SPC balljoint replacement kit - upgraded non-zerk sealed joint design 25002 -Feb. 3/ 2024: 4x KC Wire Hiders, for roof rack lighting Feb. 13/2024: New ditch lights, on new Rago Fabrication Extension brackets. 3inch Quad Row Amber Pods from LED-Club. 32W 3200Lm 16-LED Spot Beam. Replacing 3inch EVERGEAR clear lens ditch light pods w/ yellow lamix-x In progress: 4th, 5th, and 6th set of off road lights Electrical components and wiring purchased, not started -roof rack scene lighting - EVERGEAR ea. 1,350 lumens, 30w, 3-¾" round floods. Custom, side mounted w/ galvanized flat bar And -roof rack upper ditch lights - 3inch Quad Row Amber Pods from LED-Club. 32W 3200Lm 16-LED Spot Beam. Bar clamp mounted to front corners And -roof rack reverse amber pods / secondary hazard lights. 20W 2000Lm 2-LED Spot Beam. Bar clamp mounted to rear side And -roof rack F1 smoked chase light w/ lighting effects. Custom bolted to rear side -POR15 rust proofing line-up, 3-step process PAUSED until 70⁰ weather Bought, in the garage queue: -BlueFire 6-Circuit Fuse Block with LED Indicator & Protection Cover -Blue Sea Systems 100A Circuit Breaker w/ reset lever -Rust prevention •New can POR15, 2x Black Fluid Film, long spray nozzle attachments, 2x PB Surface Shield, 1x Chainwax •partially used POR15 Degreaser, Metal Prep Wanted - PerryParts or Wheelers bump stops, self fabricated limb risers (seasonal, removable), 1" body lift, powder coated center winch bumper w/ large bar (got no tss), rear steel bumper w/ tire carrier for an LT285 Kumho on steely, sliders, bolt on cat shields
    Any of you good folks know if you can swap out SPC UCA "OG" zerk greased balljoints, for the new sealed boot model? I would think there's a new replacement kit compatible, just like the OG replacement kit I already purchased.

    Screenshot_20230730-172841.png
    IMG_20230730_172425803.jpg
     
    redneck pilot and Old Tanker like this.
  20. Jul 30, 2023 at 6:53 PM
    #20
    kolter45

    kolter45 Inferno Pro & 4.0 Tacoma

    Joined:
    May 7, 2022
    Member:
    #26975
    Messages:
    702
    Gender:
    Male
    Denver
    Vehicle:
    Inferno Pro & BRM Sport
    The ones meant for the old tubular uca? :notsure:l’d call them & ask. That’s the only way to tell for sure
     
    Last edited: Jul 30, 2023
  21. Jul 30, 2023 at 7:16 PM
    #21
    kolter45

    kolter45 Inferno Pro & 4.0 Tacoma

    Joined:
    May 7, 2022
    Member:
    #26975
    Messages:
    702
    Gender:
    Male
    Denver
    Vehicle:
    Inferno Pro & BRM Sport
    I want to explain the process for return if you buy SPC UCAs & have issues

    If you buy them - it must be a dealer on SPCs sponser list. I got mine from a friends off road shop & they gave me shit & in the end said I was okay. They’ll ask for a receipt & double check the store isn’t selling the item below the price they demand. So talk to the person you bought it from first.

    I had to submit a photo before the UCAs were put on my truck. I was lucky & had snapped a photo of them brand new. I used that & it cleared me.

    Then I sent a video of the bushings making noises installed & it was the last step.

    They make a great product if it’s problem free! Again, this was on my taco
     
    djwantke likes this.
  22. Jul 30, 2023 at 10:56 PM
    #22
    djwantke

    djwantke New Member

    Joined:
    Jan 31, 2021
    Member:
    #19487
    Messages:
    3,535
    Gender:
    Male
    Maple Ridge, British Columbia
    Vehicle:
    2016 4Runner Trail Premium
    Bought brand new 2016 After May 2021: -Approx 3" lift/level: Bilstein 5100's, OME 2884 590lb 3" front lift springs, SPC UCA's, ICON 158506 2" lift rear coils, diff drop -Mickey Thompson Baja ATZ LT285/70R17 Load E -Mickey Thompson Sidebiter ll 17x9, 0 offset, 5 backspace -Pro Comp black spline lugs ^installed by 4WheelParts^ -New brakes and rotors by brake shop -4-piece ARB skid kit -Smittybilt 2" nerf steps -MBRP black exhaust tip, chopped OEM -Drivers side OEM FJ oh shit handle -All blacked out emblems -Blacked out roof rails -4x WeatherTech window rain guards -OEM custom rear mud flap deletes -KICK BACK MUD FLAPS 12" WIDE - BLACK TOP AND BLACK WEIGHT -FRAM EXTRA GUARD CA10835 engine air filter -1797 LED tricolor fog bulbs Yellow 3000K White 6000K Blue 15000K 28W 4000LM -Armour paint lower rear bumper -Front bumper high stage high clearance cut -Fenders cut straight across, pink reservoir sprayed black -4Runner Lifestyle sequential fog fangs -4Runner Lifestyle smoked taillight decals -Pedal Commander -Rear passenger cargo mounted 120v truck tire pump -4x Spidertrax 1.25" black aluminum wheel spacers -Yota Twins Paracord Hatch Strap sand camo -Teton Workshop hard anodized matte black aluminum shift knob -Ditch flood lights 4 LED 20w 1400lm w/ OEM hood mounts on OEM style dash switch -Backup flood lights under bumper 6 LED 18w 1500lm on OEM style dash switch -Body Mount Chop; cut, weld, paint -Fender mount chop, re-weld, paint -Fender Liner cut behind wheel (I cut liner in front of wheel clean off at top of viper cut) -Wheel well firewall hammering, painting ^done by Arc One Industries^ -valance cap trim -Agency6 Black Shackle Block 2" US Certified 6061 T6 CNC machined aluminum -DRT fab universal hitch skid -ACDelco inner tie rods, outer tie rods, bellows -Full Dr. KDSS switch kit -March 31 Behind grille 13-1/4" 32 LED light bar + wide-angle, eagle-eye lens 6000lm on OEM style dash switch -RAA Powder coated steel roof rack cargo basket, 1" side rails, 64" x 39" x 6", 250lb limit -roof gas can, water can, shovel -PEAKTOW PTT0063 Hitch Mount Cargo Carrier 51-1/2 x 17-1/2 x 4 inches 500 lbs. Capacity (trips only) -July/2023: purchased first needed SPC balljoint replacement kit - newly released, upgraded non-zerk sealed joints 25002 -July 15/2023: The Original Universal EZ Flares, 1". All four corners -Dec. 2023: removed bumper cover and crash bar, drilled frame, installed Apex Overland KDSS Recovery Points -Jan. 2024: SPC balljoint replacement kit - upgraded non-zerk sealed joint design 25002 -Feb. 3/ 2024: 4x KC Wire Hiders, for roof rack lighting Feb. 13/2024: New ditch lights, on new Rago Fabrication Extension brackets. 3inch Quad Row Amber Pods from LED-Club. 32W 3200Lm 16-LED Spot Beam. Replacing 3inch EVERGEAR clear lens ditch light pods w/ yellow lamix-x In progress: 4th, 5th, and 6th set of off road lights Electrical components and wiring purchased, not started -roof rack scene lighting - EVERGEAR ea. 1,350 lumens, 30w, 3-¾" round floods. Custom, side mounted w/ galvanized flat bar And -roof rack upper ditch lights - 3inch Quad Row Amber Pods from LED-Club. 32W 3200Lm 16-LED Spot Beam. Bar clamp mounted to front corners And -roof rack reverse amber pods / secondary hazard lights. 20W 2000Lm 2-LED Spot Beam. Bar clamp mounted to rear side And -roof rack F1 smoked chase light w/ lighting effects. Custom bolted to rear side -POR15 rust proofing line-up, 3-step process PAUSED until 70⁰ weather Bought, in the garage queue: -BlueFire 6-Circuit Fuse Block with LED Indicator & Protection Cover -Blue Sea Systems 100A Circuit Breaker w/ reset lever -Rust prevention •New can POR15, 2x Black Fluid Film, long spray nozzle attachments, 2x PB Surface Shield, 1x Chainwax •partially used POR15 Degreaser, Metal Prep Wanted - PerryParts or Wheelers bump stops, self fabricated limb risers (seasonal, removable), 1" body lift, powder coated center winch bumper w/ large bar (got no tss), rear steel bumper w/ tire carrier for an LT285 Kumho on steely, sliders, bolt on cat shields
    Thanks man!

    I've been one of the lucky ones, my balljoints have lasted 2.5 years and I have virtually no play when jacked from lca, as well as prybar under tire. They leak grease tho, especially the one side that I blew the seal over greasing like a rookie :).

    When you say bushing were making noise, you talking about the two bushings, or the balljoint in the boot?

    Also what did the noise sound like!?
    I'm trying to diagnose my "grinding" noise

    TY
     
    kolter45 likes this.
  23. Jul 31, 2023 at 9:27 AM
    #23
    djwantke

    djwantke New Member

    Joined:
    Jan 31, 2021
    Member:
    #19487
    Messages:
    3,535
    Gender:
    Male
    Maple Ridge, British Columbia
    Vehicle:
    2016 4Runner Trail Premium
    Bought brand new 2016 After May 2021: -Approx 3" lift/level: Bilstein 5100's, OME 2884 590lb 3" front lift springs, SPC UCA's, ICON 158506 2" lift rear coils, diff drop -Mickey Thompson Baja ATZ LT285/70R17 Load E -Mickey Thompson Sidebiter ll 17x9, 0 offset, 5 backspace -Pro Comp black spline lugs ^installed by 4WheelParts^ -New brakes and rotors by brake shop -4-piece ARB skid kit -Smittybilt 2" nerf steps -MBRP black exhaust tip, chopped OEM -Drivers side OEM FJ oh shit handle -All blacked out emblems -Blacked out roof rails -4x WeatherTech window rain guards -OEM custom rear mud flap deletes -KICK BACK MUD FLAPS 12" WIDE - BLACK TOP AND BLACK WEIGHT -FRAM EXTRA GUARD CA10835 engine air filter -1797 LED tricolor fog bulbs Yellow 3000K White 6000K Blue 15000K 28W 4000LM -Armour paint lower rear bumper -Front bumper high stage high clearance cut -Fenders cut straight across, pink reservoir sprayed black -4Runner Lifestyle sequential fog fangs -4Runner Lifestyle smoked taillight decals -Pedal Commander -Rear passenger cargo mounted 120v truck tire pump -4x Spidertrax 1.25" black aluminum wheel spacers -Yota Twins Paracord Hatch Strap sand camo -Teton Workshop hard anodized matte black aluminum shift knob -Ditch flood lights 4 LED 20w 1400lm w/ OEM hood mounts on OEM style dash switch -Backup flood lights under bumper 6 LED 18w 1500lm on OEM style dash switch -Body Mount Chop; cut, weld, paint -Fender mount chop, re-weld, paint -Fender Liner cut behind wheel (I cut liner in front of wheel clean off at top of viper cut) -Wheel well firewall hammering, painting ^done by Arc One Industries^ -valance cap trim -Agency6 Black Shackle Block 2" US Certified 6061 T6 CNC machined aluminum -DRT fab universal hitch skid -ACDelco inner tie rods, outer tie rods, bellows -Full Dr. KDSS switch kit -March 31 Behind grille 13-1/4" 32 LED light bar + wide-angle, eagle-eye lens 6000lm on OEM style dash switch -RAA Powder coated steel roof rack cargo basket, 1" side rails, 64" x 39" x 6", 250lb limit -roof gas can, water can, shovel -PEAKTOW PTT0063 Hitch Mount Cargo Carrier 51-1/2 x 17-1/2 x 4 inches 500 lbs. Capacity (trips only) -July/2023: purchased first needed SPC balljoint replacement kit - newly released, upgraded non-zerk sealed joints 25002 -July 15/2023: The Original Universal EZ Flares, 1". All four corners -Dec. 2023: removed bumper cover and crash bar, drilled frame, installed Apex Overland KDSS Recovery Points -Jan. 2024: SPC balljoint replacement kit - upgraded non-zerk sealed joint design 25002 -Feb. 3/ 2024: 4x KC Wire Hiders, for roof rack lighting Feb. 13/2024: New ditch lights, on new Rago Fabrication Extension brackets. 3inch Quad Row Amber Pods from LED-Club. 32W 3200Lm 16-LED Spot Beam. Replacing 3inch EVERGEAR clear lens ditch light pods w/ yellow lamix-x In progress: 4th, 5th, and 6th set of off road lights Electrical components and wiring purchased, not started -roof rack scene lighting - EVERGEAR ea. 1,350 lumens, 30w, 3-¾" round floods. Custom, side mounted w/ galvanized flat bar And -roof rack upper ditch lights - 3inch Quad Row Amber Pods from LED-Club. 32W 3200Lm 16-LED Spot Beam. Bar clamp mounted to front corners And -roof rack reverse amber pods / secondary hazard lights. 20W 2000Lm 2-LED Spot Beam. Bar clamp mounted to rear side And -roof rack F1 smoked chase light w/ lighting effects. Custom bolted to rear side -POR15 rust proofing line-up, 3-step process PAUSED until 70⁰ weather Bought, in the garage queue: -BlueFire 6-Circuit Fuse Block with LED Indicator & Protection Cover -Blue Sea Systems 100A Circuit Breaker w/ reset lever -Rust prevention •New can POR15, 2x Black Fluid Film, long spray nozzle attachments, 2x PB Surface Shield, 1x Chainwax •partially used POR15 Degreaser, Metal Prep Wanted - PerryParts or Wheelers bump stops, self fabricated limb risers (seasonal, removable), 1" body lift, powder coated center winch bumper w/ large bar (got no tss), rear steel bumper w/ tire carrier for an LT285 Kumho on steely, sliders, bolt on cat shields
    update
     
  24. Jul 31, 2023 at 1:21 PM
    #24
    djwantke

    djwantke New Member

    Joined:
    Jan 31, 2021
    Member:
    #19487
    Messages:
    3,535
    Gender:
    Male
    Maple Ridge, British Columbia
    Vehicle:
    2016 4Runner Trail Premium
    Bought brand new 2016 After May 2021: -Approx 3" lift/level: Bilstein 5100's, OME 2884 590lb 3" front lift springs, SPC UCA's, ICON 158506 2" lift rear coils, diff drop -Mickey Thompson Baja ATZ LT285/70R17 Load E -Mickey Thompson Sidebiter ll 17x9, 0 offset, 5 backspace -Pro Comp black spline lugs ^installed by 4WheelParts^ -New brakes and rotors by brake shop -4-piece ARB skid kit -Smittybilt 2" nerf steps -MBRP black exhaust tip, chopped OEM -Drivers side OEM FJ oh shit handle -All blacked out emblems -Blacked out roof rails -4x WeatherTech window rain guards -OEM custom rear mud flap deletes -KICK BACK MUD FLAPS 12" WIDE - BLACK TOP AND BLACK WEIGHT -FRAM EXTRA GUARD CA10835 engine air filter -1797 LED tricolor fog bulbs Yellow 3000K White 6000K Blue 15000K 28W 4000LM -Armour paint lower rear bumper -Front bumper high stage high clearance cut -Fenders cut straight across, pink reservoir sprayed black -4Runner Lifestyle sequential fog fangs -4Runner Lifestyle smoked taillight decals -Pedal Commander -Rear passenger cargo mounted 120v truck tire pump -4x Spidertrax 1.25" black aluminum wheel spacers -Yota Twins Paracord Hatch Strap sand camo -Teton Workshop hard anodized matte black aluminum shift knob -Ditch flood lights 4 LED 20w 1400lm w/ OEM hood mounts on OEM style dash switch -Backup flood lights under bumper 6 LED 18w 1500lm on OEM style dash switch -Body Mount Chop; cut, weld, paint -Fender mount chop, re-weld, paint -Fender Liner cut behind wheel (I cut liner in front of wheel clean off at top of viper cut) -Wheel well firewall hammering, painting ^done by Arc One Industries^ -valance cap trim -Agency6 Black Shackle Block 2" US Certified 6061 T6 CNC machined aluminum -DRT fab universal hitch skid -ACDelco inner tie rods, outer tie rods, bellows -Full Dr. KDSS switch kit -March 31 Behind grille 13-1/4" 32 LED light bar + wide-angle, eagle-eye lens 6000lm on OEM style dash switch -RAA Powder coated steel roof rack cargo basket, 1" side rails, 64" x 39" x 6", 250lb limit -roof gas can, water can, shovel -PEAKTOW PTT0063 Hitch Mount Cargo Carrier 51-1/2 x 17-1/2 x 4 inches 500 lbs. Capacity (trips only) -July/2023: purchased first needed SPC balljoint replacement kit - newly released, upgraded non-zerk sealed joints 25002 -July 15/2023: The Original Universal EZ Flares, 1". All four corners -Dec. 2023: removed bumper cover and crash bar, drilled frame, installed Apex Overland KDSS Recovery Points -Jan. 2024: SPC balljoint replacement kit - upgraded non-zerk sealed joint design 25002 -Feb. 3/ 2024: 4x KC Wire Hiders, for roof rack lighting Feb. 13/2024: New ditch lights, on new Rago Fabrication Extension brackets. 3inch Quad Row Amber Pods from LED-Club. 32W 3200Lm 16-LED Spot Beam. Replacing 3inch EVERGEAR clear lens ditch light pods w/ yellow lamix-x In progress: 4th, 5th, and 6th set of off road lights Electrical components and wiring purchased, not started -roof rack scene lighting - EVERGEAR ea. 1,350 lumens, 30w, 3-¾" round floods. Custom, side mounted w/ galvanized flat bar And -roof rack upper ditch lights - 3inch Quad Row Amber Pods from LED-Club. 32W 3200Lm 16-LED Spot Beam. Bar clamp mounted to front corners And -roof rack reverse amber pods / secondary hazard lights. 20W 2000Lm 2-LED Spot Beam. Bar clamp mounted to rear side And -roof rack F1 smoked chase light w/ lighting effects. Custom bolted to rear side -POR15 rust proofing line-up, 3-step process PAUSED until 70⁰ weather Bought, in the garage queue: -BlueFire 6-Circuit Fuse Block with LED Indicator & Protection Cover -Blue Sea Systems 100A Circuit Breaker w/ reset lever -Rust prevention •New can POR15, 2x Black Fluid Film, long spray nozzle attachments, 2x PB Surface Shield, 1x Chainwax •partially used POR15 Degreaser, Metal Prep Wanted - PerryParts or Wheelers bump stops, self fabricated limb risers (seasonal, removable), 1" body lift, powder coated center winch bumper w/ large bar (got no tss), rear steel bumper w/ tire carrier for an LT285 Kumho on steely, sliders, bolt on cat shields
    God is good. New improved 25002 non-zerk SPC balljoint replacement kit has already arrived in The Ridge for pickup tonight, same price straight swap!
     
  25. Jul 31, 2023 at 6:31 PM
    #25
    kolter45

    kolter45 Inferno Pro & 4.0 Tacoma

    Joined:
    May 7, 2022
    Member:
    #26975
    Messages:
    702
    Gender:
    Male
    Denver
    Vehicle:
    Inferno Pro & BRM Sport
    The 2 bushings for the uca bolt. They had a bad batch for about a year. I bought mine because I wanted to support local. It’s was that notorious clunk noise pulling up to a stop. Even my neighbor was like wtf man! He’s an f150 guy but loves my Tacoma. It’s the 2.5 gen with the 4.0 just like my 4Runner. Lift looks awesome now but it was some work getting this far
     
  26. Jul 31, 2023 at 9:21 PM
    #26
    MyWyfsRnnr

    MyWyfsRnnr Have you seen the mall?

    Joined:
    Feb 26, 2019
    Member:
    #8958
    Messages:
    1,025
    Gender:
    Male
    First Name:
    Chris
    Citrus Heights
    Vehicle:
    2018 4Runner TRD
    Prinsu, Blacked-out taillights, tinted fronts, BudBuilt Sliders, BudBuilt Skids, OME lift, 275/70/17 KO2's, LED interior, C4 Fab Diff Skid, Dvr Grab Handle, AnyTime Backup Camera, Badge Overlays, Wet Okole Covers
    I have installed a ton of them and I really like them for the adjustability etc. I also like carrying one replacement for the trail that is conceivable to replace with limited tools. You aren't changing a uniball on the trail very easily haha. I had a SPC ball joint failure due to not greasing sufficiently. Totally on me. I've been 100% happy with mine and have not gotten a defective one out of the 10+ I've installed for customers. (Not using it doesn't happen, I just have not seen an issue yet; to be fair, I haven't seen any issues with the delta joints either).
     
    Superdave1.0, djwantke and kolter45 like this.
  27. Feb 20, 2024 at 1:34 PM
    #27
    Horhay

    Horhay New Member

    Joined:
    Feb 20, 2024
    Member:
    #38655
    Messages:
    1
    Gender:
    Male
    North Carolina
    Vehicle:
    2015 Inferno 4Runner TRD Pro
    Saw this thread and wanted to contribute. I got less than 20K miles out of mine before the bushings started to shift around and the ball joints failed. SPC offered to partially warranty them but after the $275 core charge plus the cost to install and an alignment, I'm out over $700.

    For reference, I've got a 2015 TRDp.
     
  28. Feb 21, 2024 at 1:03 PM
    #28
    djwantke

    djwantke New Member

    Joined:
    Jan 31, 2021
    Member:
    #19487
    Messages:
    3,535
    Gender:
    Male
    Maple Ridge, British Columbia
    Vehicle:
    2016 4Runner Trail Premium
    Bought brand new 2016 After May 2021: -Approx 3" lift/level: Bilstein 5100's, OME 2884 590lb 3" front lift springs, SPC UCA's, ICON 158506 2" lift rear coils, diff drop -Mickey Thompson Baja ATZ LT285/70R17 Load E -Mickey Thompson Sidebiter ll 17x9, 0 offset, 5 backspace -Pro Comp black spline lugs ^installed by 4WheelParts^ -New brakes and rotors by brake shop -4-piece ARB skid kit -Smittybilt 2" nerf steps -MBRP black exhaust tip, chopped OEM -Drivers side OEM FJ oh shit handle -All blacked out emblems -Blacked out roof rails -4x WeatherTech window rain guards -OEM custom rear mud flap deletes -KICK BACK MUD FLAPS 12" WIDE - BLACK TOP AND BLACK WEIGHT -FRAM EXTRA GUARD CA10835 engine air filter -1797 LED tricolor fog bulbs Yellow 3000K White 6000K Blue 15000K 28W 4000LM -Armour paint lower rear bumper -Front bumper high stage high clearance cut -Fenders cut straight across, pink reservoir sprayed black -4Runner Lifestyle sequential fog fangs -4Runner Lifestyle smoked taillight decals -Pedal Commander -Rear passenger cargo mounted 120v truck tire pump -4x Spidertrax 1.25" black aluminum wheel spacers -Yota Twins Paracord Hatch Strap sand camo -Teton Workshop hard anodized matte black aluminum shift knob -Ditch flood lights 4 LED 20w 1400lm w/ OEM hood mounts on OEM style dash switch -Backup flood lights under bumper 6 LED 18w 1500lm on OEM style dash switch -Body Mount Chop; cut, weld, paint -Fender mount chop, re-weld, paint -Fender Liner cut behind wheel (I cut liner in front of wheel clean off at top of viper cut) -Wheel well firewall hammering, painting ^done by Arc One Industries^ -valance cap trim -Agency6 Black Shackle Block 2" US Certified 6061 T6 CNC machined aluminum -DRT fab universal hitch skid -ACDelco inner tie rods, outer tie rods, bellows -Full Dr. KDSS switch kit -March 31 Behind grille 13-1/4" 32 LED light bar + wide-angle, eagle-eye lens 6000lm on OEM style dash switch -RAA Powder coated steel roof rack cargo basket, 1" side rails, 64" x 39" x 6", 250lb limit -roof gas can, water can, shovel -PEAKTOW PTT0063 Hitch Mount Cargo Carrier 51-1/2 x 17-1/2 x 4 inches 500 lbs. Capacity (trips only) -July/2023: purchased first needed SPC balljoint replacement kit - newly released, upgraded non-zerk sealed joints 25002 -July 15/2023: The Original Universal EZ Flares, 1". All four corners -Dec. 2023: removed bumper cover and crash bar, drilled frame, installed Apex Overland KDSS Recovery Points -Jan. 2024: SPC balljoint replacement kit - upgraded non-zerk sealed joint design 25002 -Feb. 3/ 2024: 4x KC Wire Hiders, for roof rack lighting Feb. 13/2024: New ditch lights, on new Rago Fabrication Extension brackets. 3inch Quad Row Amber Pods from LED-Club. 32W 3200Lm 16-LED Spot Beam. Replacing 3inch EVERGEAR clear lens ditch light pods w/ yellow lamix-x In progress: 4th, 5th, and 6th set of off road lights Electrical components and wiring purchased, not started -roof rack scene lighting - EVERGEAR ea. 1,350 lumens, 30w, 3-¾" round floods. Custom, side mounted w/ galvanized flat bar And -roof rack upper ditch lights - 3inch Quad Row Amber Pods from LED-Club. 32W 3200Lm 16-LED Spot Beam. Bar clamp mounted to front corners And -roof rack reverse amber pods / secondary hazard lights. 20W 2000Lm 2-LED Spot Beam. Bar clamp mounted to rear side And -roof rack F1 smoked chase light w/ lighting effects. Custom bolted to rear side -POR15 rust proofing line-up, 3-step process PAUSED until 70⁰ weather Bought, in the garage queue: -BlueFire 6-Circuit Fuse Block with LED Indicator & Protection Cover -Blue Sea Systems 100A Circuit Breaker w/ reset lever -Rust prevention •New can POR15, 2x Black Fluid Film, long spray nozzle attachments, 2x PB Surface Shield, 1x Chainwax •partially used POR15 Degreaser, Metal Prep Wanted - PerryParts or Wheelers bump stops, self fabricated limb risers (seasonal, removable), 1" body lift, powder coated center winch bumper w/ large bar (got no tss), rear steel bumper w/ tire carrier for an LT285 Kumho on steely, sliders, bolt on cat shields
    new sealed joints done

    IMG_20240115_161645_026.jpg
    Screenshot_20240127-123956.png
     
  29. Feb 21, 2024 at 2:23 PM
    #29
    Slopemaster

    Slopemaster Slope Survivalist

    Joined:
    Mar 20, 2021
    Member:
    #20442
    Messages:
    3,090
    Gender:
    Male
    Idaho
    Vehicle:
    2018 SR5
    265-70-17 Ridge Grapplers, TRD Pro rims, 3M precut bra, N-Fab nerf/steps
    I’ll stick with my OEM control arms. No maintenance or squeaking.
     
    semprenissart, djwantke and Rocko9999 like this.
  30. Feb 21, 2024 at 2:39 PM
    #30
    djwantke

    djwantke New Member

    Joined:
    Jan 31, 2021
    Member:
    #19487
    Messages:
    3,535
    Gender:
    Male
    Maple Ridge, British Columbia
    Vehicle:
    2016 4Runner Trail Premium
    Bought brand new 2016 After May 2021: -Approx 3" lift/level: Bilstein 5100's, OME 2884 590lb 3" front lift springs, SPC UCA's, ICON 158506 2" lift rear coils, diff drop -Mickey Thompson Baja ATZ LT285/70R17 Load E -Mickey Thompson Sidebiter ll 17x9, 0 offset, 5 backspace -Pro Comp black spline lugs ^installed by 4WheelParts^ -New brakes and rotors by brake shop -4-piece ARB skid kit -Smittybilt 2" nerf steps -MBRP black exhaust tip, chopped OEM -Drivers side OEM FJ oh shit handle -All blacked out emblems -Blacked out roof rails -4x WeatherTech window rain guards -OEM custom rear mud flap deletes -KICK BACK MUD FLAPS 12" WIDE - BLACK TOP AND BLACK WEIGHT -FRAM EXTRA GUARD CA10835 engine air filter -1797 LED tricolor fog bulbs Yellow 3000K White 6000K Blue 15000K 28W 4000LM -Armour paint lower rear bumper -Front bumper high stage high clearance cut -Fenders cut straight across, pink reservoir sprayed black -4Runner Lifestyle sequential fog fangs -4Runner Lifestyle smoked taillight decals -Pedal Commander -Rear passenger cargo mounted 120v truck tire pump -4x Spidertrax 1.25" black aluminum wheel spacers -Yota Twins Paracord Hatch Strap sand camo -Teton Workshop hard anodized matte black aluminum shift knob -Ditch flood lights 4 LED 20w 1400lm w/ OEM hood mounts on OEM style dash switch -Backup flood lights under bumper 6 LED 18w 1500lm on OEM style dash switch -Body Mount Chop; cut, weld, paint -Fender mount chop, re-weld, paint -Fender Liner cut behind wheel (I cut liner in front of wheel clean off at top of viper cut) -Wheel well firewall hammering, painting ^done by Arc One Industries^ -valance cap trim -Agency6 Black Shackle Block 2" US Certified 6061 T6 CNC machined aluminum -DRT fab universal hitch skid -ACDelco inner tie rods, outer tie rods, bellows -Full Dr. KDSS switch kit -March 31 Behind grille 13-1/4" 32 LED light bar + wide-angle, eagle-eye lens 6000lm on OEM style dash switch -RAA Powder coated steel roof rack cargo basket, 1" side rails, 64" x 39" x 6", 250lb limit -roof gas can, water can, shovel -PEAKTOW PTT0063 Hitch Mount Cargo Carrier 51-1/2 x 17-1/2 x 4 inches 500 lbs. Capacity (trips only) -July/2023: purchased first needed SPC balljoint replacement kit - newly released, upgraded non-zerk sealed joints 25002 -July 15/2023: The Original Universal EZ Flares, 1". All four corners -Dec. 2023: removed bumper cover and crash bar, drilled frame, installed Apex Overland KDSS Recovery Points -Jan. 2024: SPC balljoint replacement kit - upgraded non-zerk sealed joint design 25002 -Feb. 3/ 2024: 4x KC Wire Hiders, for roof rack lighting Feb. 13/2024: New ditch lights, on new Rago Fabrication Extension brackets. 3inch Quad Row Amber Pods from LED-Club. 32W 3200Lm 16-LED Spot Beam. Replacing 3inch EVERGEAR clear lens ditch light pods w/ yellow lamix-x In progress: 4th, 5th, and 6th set of off road lights Electrical components and wiring purchased, not started -roof rack scene lighting - EVERGEAR ea. 1,350 lumens, 30w, 3-¾" round floods. Custom, side mounted w/ galvanized flat bar And -roof rack upper ditch lights - 3inch Quad Row Amber Pods from LED-Club. 32W 3200Lm 16-LED Spot Beam. Bar clamp mounted to front corners And -roof rack reverse amber pods / secondary hazard lights. 20W 2000Lm 2-LED Spot Beam. Bar clamp mounted to rear side And -roof rack F1 smoked chase light w/ lighting effects. Custom bolted to rear side -POR15 rust proofing line-up, 3-step process PAUSED until 70⁰ weather Bought, in the garage queue: -BlueFire 6-Circuit Fuse Block with LED Indicator & Protection Cover -Blue Sea Systems 100A Circuit Breaker w/ reset lever -Rust prevention •New can POR15, 2x Black Fluid Film, long spray nozzle attachments, 2x PB Surface Shield, 1x Chainwax •partially used POR15 Degreaser, Metal Prep Wanted - PerryParts or Wheelers bump stops, self fabricated limb risers (seasonal, removable), 1" body lift, powder coated center winch bumper w/ large bar (got no tss), rear steel bumper w/ tire carrier for an LT285 Kumho on steely, sliders, bolt on cat shields
    Very true, OE quality often doesn't have these notorious aftermarket issues.
    I ain't using OE control arms on a 3" lift and 285's on Spidertrax tho :p
     

Products Discussed in

To Top