1. Welcome to 4Runners.com!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all 4Runner discussion topics
    • Transfer over your build thread from a different forum to this one
    • Communicate privately with other 4Runner owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

Fender gap looking very huge with OME BP-51

Discussion in '5th Gen 4Runners (2010-2024)' started by nnnaaavvv, Jul 10, 2025 at 8:45 AM.

  1. Jul 12, 2025 at 10:23 AM
    #31
    Gman2530

    Gman2530 New Member

    Joined:
    Mar 23, 2023
    Member:
    #31923
    Messages:
    220
    Gender:
    Male
    First Name:
    Gary
    Vehicle:
    2018 SR5 4wd 4Runner
    IMG_5107.jpg IMG_5107.jpg I totally understand. I think most of us truly work hard on getting the stance that we want and the stance that works best for us because of the weight that I carry and where I go off Roading, I like the rear a little bit higher for departure angle
    When I’m driving, I don’t feel the rake at all and when I’m fully loaded as I mentioned with about 400 pounds of gear which I find unbelievable that I carry :angrygirl:
    It feels really good no squatting
     
    nnnaaavvv[OP] likes this.
  2. Jul 12, 2025 at 10:25 AM
    #32
    Gman2530

    Gman2530 New Member

    Joined:
    Mar 23, 2023
    Member:
    #31923
    Messages:
    220
    Gender:
    Male
    First Name:
    Gary
    Vehicle:
    2018 SR5 4wd 4Runner
    Eibach does make an adjustable set rear spring
     
  3. Jul 12, 2025 at 7:25 PM
    #33
    nimby

    nimby in the drink

    Joined:
    Mar 27, 2017
    Member:
    #3777
    Messages:
    4,928
    First Name:
    Jake
    California
    Vehicle:
    2018 SR5P
    Who did the install? You or a shop?

    If it was a shop, did they sell you the kit?
     
  4. Jul 12, 2025 at 10:08 PM
    #34
    nnnaaavvv

    nnnaaavvv [OP] New Member

    Joined:
    Apr 21, 2025
    Member:
    #46679
    Messages:
    20
    Gender:
    Male
    Vehicle:
    2015 4Runner Limited
    None
    It was the shop, I think they added the kit. Here are all the items they mentioned in the invoice.

    IMG_4181.jpg
    IMG_4182.jpg
     
  5. Jul 13, 2025 at 8:58 AM
    #35
    nimby

    nimby in the drink

    Joined:
    Mar 27, 2017
    Member:
    #3777
    Messages:
    4,928
    First Name:
    Jake
    California
    Vehicle:
    2018 SR5P
    I tried looking up some part numbers on the ARB/OME BP-51 coils. Their descriptions were really vague and convoluted and I couldn't make much sense of expected lift height from each coil option they had in the time I had.

    If I were you, I'd go back to the shop that installed this and tell them you you'd like less lift, if possible. For the front, that probably means adjusting the front shocks down (if there's room). For the back, that probably means replacing the rear coil with either a smaller lift coil and/or one with a lighter load rating. The rear coils do not have to be OME either. They can put on any rear coil that meets your preference on lift height and load rating. Bilstein, Eibach, and Dobinson all make rear lift coils for our trucks that are worth checking out.

    All the expensive components (the shocks) can remain in place. They will work with these adjustments.

    But talk to your shop first to discuss these possibilities.
     
    nnnaaavvv[OP] likes this.
  6. Jul 13, 2025 at 11:11 AM
    #36
    nnnaaavvv

    nnnaaavvv [OP] New Member

    Joined:
    Apr 21, 2025
    Member:
    #46679
    Messages:
    20
    Gender:
    Male
    Vehicle:
    2015 4Runner Limited
    None
    I am thinking that too, will be going for the alignment coming Friday (after 300-400mi) to the shop and will talk to them.
     
  7. Jul 13, 2025 at 7:39 PM
    #37
    nnnaaavvv

    nnnaaavvv [OP] New Member

    Joined:
    Apr 21, 2025
    Member:
    #46679
    Messages:
    20
    Gender:
    Male
    Vehicle:
    2015 4Runner Limited
    None
    Update: Drove ~250mi

    Suspension Height Summary (Hub-to-Fender Measurements)

    IMG_4185.jpg

    The BP-51 setup has begun to settle after ~250 miles, showing a reduction of 0.74″ front and 0.72″ rear from initial post-install measurements. The current lift over factory-new Limited height is approximately +2.25″ front and +1.4″ rear
     

Products Discussed in

To Top