1. Welcome to 4Runners.com!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all 4Runner discussion topics
    • Transfer over your build thread from a different forum to this one
    • Communicate privately with other 4Runner owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

What’s your lighting setup looking like?

Discussion in '5th Gen 4Runners (2010-2024)' started by Laith027, Oct 22, 2025.

  1. Oct 22, 2025 at 8:19 AM
    #1
    Laith027

    Laith027 [OP] New Member

    Joined:
    Oct 16, 2025
    Member:
    #49506
    Messages:
    8
    Gender:
    Male
    Vehicle:
    2018 4Runner TRD Offroad
    Curious to know about the different lighting setups everyone is rocking.

    I am contemplating the following setup:
    1) 20” white light bar behind the lower grill,
    2) amber fog lights to replace OEM fog lights

    something similar to the attached

    I figure this will be enough for my use case which is mainly desert and beach drives. My rig is not for doing any serious overlanding, just a weekend warrior type thing.

    Appreciate any inputs on your lighting rigs ;)

    IMG_6503.jpg
     
    djwantke and Rocket-67 like this.
  2. Oct 22, 2025 at 8:50 AM
    #2
    Rocket-67

    Rocket-67 New Member

    Joined:
    Sep 8, 2025
    Member:
    #48912
    Messages:
    56
    Gender:
    Male
    First Name:
    Chris
    SE New Mexico
    Vehicle:
    '19 4 Runner TRD Off-road
    I recently upgraded to the led fog lights, it really was a great improvement.
    I don't do the serious off road stuff, but long streaches with lots of wildlife!
     
  3. Oct 22, 2025 at 8:56 AM
    #3
    Laith027

    Laith027 [OP] New Member

    Joined:
    Oct 16, 2025
    Member:
    #49506
    Messages:
    8
    Gender:
    Male
    Vehicle:
    2018 4Runner TRD Offroad
    White or Amber LEDs?
    Is that the only lighting mod you’ve done? If so, would you say that it’s enough?
     
    Rocket-67[QUOTED] likes this.
  4. Oct 22, 2025 at 8:59 AM
    #4
    whippersnapper02

    whippersnapper02 New Member

    Joined:
    Feb 27, 2019
    Member:
    #8982
    Messages:
    3,902
    Gender:
    Male
    First Name:
    Christian
    Vehicle:
    2019 TRDP w/Kangs brah!
    Nothing so far but the plan is to add a bar, maybe two, behind the grill and Minwin side mirror lights. I have Morimoto XB Evo headlights and OEM LED fogs for now. Yellow fogs on all the time looks lame.
     
    Rocket-67 likes this.
  5. Oct 22, 2025 at 9:16 AM
    #5
    Guppy1301

    Guppy1301 New Member

    Joined:
    Jan 2, 2023
    Member:
    #30386
    Messages:
    590
    Gender:
    Male
    Vehicle:
    Silver 2019 TRD ORP
    Bilstein 6112/5100 TSO bumper Rokmen rear LCA Northstar x2 Voltage pro booster
    I have some cheap Traveller ditch lights and Diode Dynamics Amber Pro fogs. Highly recommend the Amber Pros if you do any kind of night driving when it's rainy or foggy. I also have a 25" combo light bar in my TSO Incog bumper. Slimline XS6 I believe.
     
    4RunRap556 and Rocket-67 like this.
  6. Oct 22, 2025 at 10:15 AM
    #6
    Stoney Ranger

    Stoney Ranger Lockers? Pffft. Pizza Cutters baby

    Joined:
    Mar 19, 2021
    Member:
    #20419
    Messages:
    1,228
    Gender:
    Male
    First Name:
    Dave
    Driftless Area
    Vehicle:
    '18 SR5 Nauti Blue
    4x Rockers/Skids-Dobi-255's-Full Armor-Winch-Stickers-ALF
    17611533564948869369782935460773.jpg 17611534015328861832746879903151.jpg

    Ditto on the Diode Dynamics Amber pro fogs. The beam that is thrown is a game changer for spotting roadside critters. I figured that since I was replacing the factory foggers, I may as well get fang lights, too. The fang lights are sequential amber turn signals, too.
     
    Last edited: Oct 22, 2025
  7. Oct 22, 2025 at 10:29 AM
    #7
    Thatbassguy

    Thatbassguy New member? Really??

    Joined:
    Mar 27, 2019
    Member:
    #9314
    Messages:
    14,874
    Gender:
    Male
    First Name:
    James
    S/E Wisconsin
    Vehicle:
    2019 TRDORP, KDSS, MGM
    RSG sliders, Yakima Megawarrior basket, Black Rhino wheels, SOS Streamline bumper and skids, Warn VR EVO10S winch, OME MT64, Bilstein rear lift coils, Rigid Dually SS ditch lights, SR light bar, and Diode Dynamics SS3 fogs.
    For functional fog lights, I'd recommend Diode Dynamics SS3 in selective yellow. They're available with amber back lighting. I have the Sports, and they're a massive upgrade over stock.

    I also have a 20" Rigid SR light bar in my bumper, and Rigid D-SS ditch lights on Caliraised low profile mounts.

    Edit: picture added. This is just the factory headlights and the ditch lights. They make it like daytime for about 50' around the front of the vehicle. :D

    20200723_223036_HDR.jpg
     
    Last edited: Oct 22, 2025
  8. Oct 22, 2025 at 10:31 AM
    #8
    surfingbuddhist

    surfingbuddhist New Member

    Joined:
    Oct 31, 2022
    Member:
    #29354
    Messages:
    86
    Gender:
    Male
    First Name:
    Glen
    Vehicle:
    2020 4Runner
    upload_2025-10-22_10-30-10.png

    You can never have too many lights!! 360-degree illumination on my rig!
     
    Gman2530, icebear, Ripper238 and 10 others like this.
  9. Oct 22, 2025 at 10:35 AM
    #9
    Rocket-67

    Rocket-67 New Member

    Joined:
    Sep 8, 2025
    Member:
    #48912
    Messages:
    56
    Gender:
    Male
    First Name:
    Chris
    SE New Mexico
    Vehicle:
    '19 4 Runner TRD Off-road

    I went with amber on my fogs
     
  10. Oct 22, 2025 at 11:00 AM
    #10
    Stoney Ranger

    Stoney Ranger Lockers? Pffft. Pizza Cutters baby

    Joined:
    Mar 19, 2021
    Member:
    #20419
    Messages:
    1,228
    Gender:
    Male
    First Name:
    Dave
    Driftless Area
    Vehicle:
    '18 SR5 Nauti Blue
    4x Rockers/Skids-Dobi-255's-Full Armor-Winch-Stickers-ALF
    Holy Clark Griswold !!!
     
  11. Oct 22, 2025 at 11:32 AM
    #11
    Thacrow

    Thacrow New Member

    Joined:
    May 30, 2021
    Member:
    #21719
    Messages:
    1,923
    Gender:
    Male
    NorCal
    Vehicle:
    2021 ORP
    Speed holes
    Baja light bar. Baja Squadron in the Fogs.

    Ive wanted to put lights on the roof rack as well as rock lights but I just haven't wheeled much at night. Im always making dinner and then chilling around a fire. And ive realized I want lights just because im out of projects and thats not a good enough reason.

    20251003_065818.jpg
     
    Last edited: Oct 22, 2025
    Rocket-67 likes this.
  12. Oct 22, 2025 at 11:37 AM
    #12
    Borracho Loco

    Borracho Loco My 4Runner identifies as a Prius!

    Joined:
    Sep 23, 2023
    Member:
    #35824
    Messages:
    4,083
    Gender:
    Male
    Dallas/Ft Worth
    Vehicle:
    2023 40th Anniversary Special Edition
    Oooh look, another mod.....
    Damn bro, I bet you can see into the FUTURE with all those lights.
     
    Gman2530, Saker and Rocket-67 like this.
  13. Oct 22, 2025 at 2:03 PM
    #13
    ChessGuy

    ChessGuy New Member

    Joined:
    Oct 22, 2021
    Member:
    #23918
    Messages:
    1,721
    Gender:
    Male
    First Name:
    LR
    Houston
    Vehicle:
    2020 Venture / 2017 Tacoma
    Too many..... Performance: • Magnusum Supercharger • Gibson exhaust with dual black tip • Pedal Commander * PowerBrakes • Suspension – Old Man Emu BP-51 front and back with Medium load coils • Tires: AT3 Faulken Wildpeak – 285/70/17 • Wheels: Relations Race Wheels, RR7-H with -12 offset • Full roof rack and ladder by Westcott Design (removed the stock Yakima basket) • Molle storage panels by Rago fabrication • Front light brackets by Rago • Illuminator light bracket by Rago (roof rack location) Lights • Morimoto front and back with sequential signals • Morimoto fog lights and side mirrors with sequential signals • 40” Baja design light bar for roof rack • 20” S8 Baja design driving combo (winch location) • Squadron sport baja design ditch lights • S2 Chase lights by baja designs (mounted on roof) In the bay: • Odyssey 34-PC Battery • SDQH Aluminum billet battery terminals and bracket • Switch Pro 9100 with aluminum tray • Anytime front and back camera • ARB twin compressor Recovery & Protection: • Smittybilt X20 synthetic rope winch • Factor 55 fairlead and flatlink • Southern Style Off-road (SSO) low profile bumper • SSO stage 2 high clearance wings • Weekend warrior recovery kit by treaty oak • RCI – skid plates – entire vehicle + catalytic converter protection wings Interior: • Nano Ceramic IR – Avery Dennison Window tint – all windows • Several phone mounts • Upgraded Rear Hatch lift gate struts (ladder is heavy) • Boom blaster horn switch (featuring La cucaracha)
    Whatever you do get a Switch Pro and get all the lights going into that system else you will have all kinds of issues with batteries and wires running all over.
    I went baja all throughout on my tank.
    • 40” Baja design light bar for roof rack
    • 20” S8 Baja design driving combo (winch location)
    • Squadron sport baja design ditch lights
    • S2 Chase lights by baja designs (mounted on roof)
     
  14. Oct 22, 2025 at 3:52 PM
    #14
    Jynarik

    Jynarik I like boobies

    Joined:
    Jul 10, 2019
    Member:
    #10510
    Messages:
    2,381
    Gender:
    Male
    Austin Texas
    Vehicle:
    2019 trd pro voodoo
    Diode makes the best fogs IMO

    Baja pro ditch lights
    Diode pro fogs
    Extreme 30” bumper lightbar
    And a 20” behind the grill lightbar just for fun
     
  15. Oct 22, 2025 at 4:12 PM
    #15
    djwantke

    djwantke New Member

    Joined:
    Jan 31, 2021
    Member:
    #19487
    Messages:
    5,357
    Gender:
    Male
    Maple Ridge, British Columbia
    Vehicle:
    2016 4Runner Trail Premium
    Bought brand new 2016 After May 2021: -Approx 3" lift/level: Bilstein 5100's, OME 2884 590lb 3" front lift springs, SPC UCA's, ICON 158506 2" lift rear coils, diff drop -Mickey Thompson Baja ATZ LT285/70R17 Load E -Mickey Thompson Sidebiter ll 17x9, 0 offset, 5 backspace -Pro Comp black spline lugs ^installed by 4WheelParts^ -New brakes and rotors by brake shop -4-piece ARB skid kit -Smittybilt 2" nerf steps -MBRP black exhaust tip, chopped OEM -Drivers side OEM FJ oh shit handle -All blacked out emblems -Blacked out roof rails -4x WeatherTech window rain guards -OEM custom rear mud flap deletes -KICK BACK MUD FLAPS 12" WIDE - BLACK TOP AND BLACK WEIGHT -FRAM EXTRA GUARD CA10835 engine air filter -1797 LED tricolor fog bulbs Yellow 3000K White 6000K Blue 15000K 28W 4000LM -Armour paint lower rear bumper -Front bumper high stage high clearance cut -Fenders cut straight across, pink reservoir sprayed black -4Runner Lifestyle sequential fog fangs -4Runner Lifestyle smoked taillight decals -Pedal Commander -Rear passenger cargo mounted 120v truck tire pump -4x Spidertrax 1.25" black aluminum wheel spacers -Yota Twins Paracord Hatch Strap sand camo -Teton Workshop hard anodized matte black aluminum shift knob -Ditch flood lights 4 LED 20w 1400lm w/ OEM hood mounts on OEM style dash switch -Backup flood lights under bumper 6 LED 18w 1500lm on OEM style dash switch -Body Mount Chop; cut, weld, paint -Fender mount chop, re-weld, paint -Fender Liner cut behind wheel (I cut liner in front of wheel clean off at top of viper cut) -Wheel well firewall hammering, painting ^done by Arc One Industries^ -valance cap trim -Agency6 Black Shackle Block 2" US Certified 6061 T6 CNC machined aluminum -DRT fab universal hitch skid -ACDelco inner tie rods, outer tie rods, bellows -Full Dr. KDSS switch kit -March 31 Behind grille 13-1/4" 32 LED light bar + wide-angle, eagle-eye lens 6000lm on OEM style dash switch -RAA Powder coated steel roof rack cargo basket, 1" side rails, 64" x 39" x 6", 250lb limit -roof gas can, water can, shovel -PEAKTOW PTT0063 Hitch Mount Cargo Carrier 51-1/2 x 17-1/2 x 4 inches 500 lbs. Capacity (trips only) -July/2023: purchased first needed SPC balljoint replacement kit - newly released, upgraded non-zerk sealed joints 25002 -July 15/2023: The Original Universal EZ Flares, 1". All four corners -Dec. 2023: removed bumper cover and crash bar, drilled frame, installed Apex Overland KDSS Recovery Points -Jan. 2024: SPC balljoint replacement kit - upgraded non-zerk sealed joint design 25002 -Jan. 2024: custom installed 2lb fire extinguisher between drivers seat and door -Feb. 2024: swapped interior lighting to diode dynamics led’s -Feb. 3/ 2024: 4x KC Wire Hiders, for roof rack lighting -Feb. 13/2024: double ditch lights, on new Rago Fabrication Extension brackets. -3inch Quad Row Amber Pods from LED-Club. 32W 3200Lm 16-LED Spot Beam. Existing: 3inch EVERGEAR clear lens LED pods -May 2024: custom black aluminum grille mesh installed in front of factory plastic -June 2024: custom built powder coated dom sliders -Nov. 2024: thermo-plastic rear mudflaps -Dec. 2024: rear bumper cover clearance cut, sprayed newly exposed parts black -Jan. 2025: trailer hitch removal, relocation of rear led pods to crossmember New: -Exhaust pipe chop after axle -March 2025: new SPC upper control arms, bushings, balljoints. Raised front end 0.75” via Bilstein 5100 spring seat. -April 2025: Evergear bezel-less cube ditch lights 4 LEDs 40W 3.33A 4800Lm 328’ beam distance 30° 6000k beam angle shatter & crack resistant lens -April 2025: Evergear Ultra Series light bar 27-3/4” flood spot combo 60 LEDs 60W 5A 6000Lm 1227’ beam distance Dual row, dual beam angle 30°/60° April 2025: BULLY Rock Crawler Hi-Intensity LED Utility Lights, Pair 1260 lumens @ 15w (3 x 5w CREE) each 120° flood beam waterproof, dustproof. Under hood: -Blue Fire 6-Circuit Fuse Block w/ LED Indicator & Protection Cover -Blue Sea 100A Circuit Breaker w/ reset lever In progress/in the garage queue: ~ Wanted - 80% OFFROAD Hitch Replacement Recovery Point, PerryParts or Wheelers bump stops, 1" body lift, custom dom front bumper, winch, rear dom bumper with side hoops, kdss angle correction, C or D load 35’s, bolt on cat shields
    Oh wow, someone who may run more light loads than I lol
     
  16. Oct 22, 2025 at 4:14 PM
    #16
    djwantke

    djwantke New Member

    Joined:
    Jan 31, 2021
    Member:
    #19487
    Messages:
    5,357
    Gender:
    Male
    Maple Ridge, British Columbia
    Vehicle:
    2016 4Runner Trail Premium
    Bought brand new 2016 After May 2021: -Approx 3" lift/level: Bilstein 5100's, OME 2884 590lb 3" front lift springs, SPC UCA's, ICON 158506 2" lift rear coils, diff drop -Mickey Thompson Baja ATZ LT285/70R17 Load E -Mickey Thompson Sidebiter ll 17x9, 0 offset, 5 backspace -Pro Comp black spline lugs ^installed by 4WheelParts^ -New brakes and rotors by brake shop -4-piece ARB skid kit -Smittybilt 2" nerf steps -MBRP black exhaust tip, chopped OEM -Drivers side OEM FJ oh shit handle -All blacked out emblems -Blacked out roof rails -4x WeatherTech window rain guards -OEM custom rear mud flap deletes -KICK BACK MUD FLAPS 12" WIDE - BLACK TOP AND BLACK WEIGHT -FRAM EXTRA GUARD CA10835 engine air filter -1797 LED tricolor fog bulbs Yellow 3000K White 6000K Blue 15000K 28W 4000LM -Armour paint lower rear bumper -Front bumper high stage high clearance cut -Fenders cut straight across, pink reservoir sprayed black -4Runner Lifestyle sequential fog fangs -4Runner Lifestyle smoked taillight decals -Pedal Commander -Rear passenger cargo mounted 120v truck tire pump -4x Spidertrax 1.25" black aluminum wheel spacers -Yota Twins Paracord Hatch Strap sand camo -Teton Workshop hard anodized matte black aluminum shift knob -Ditch flood lights 4 LED 20w 1400lm w/ OEM hood mounts on OEM style dash switch -Backup flood lights under bumper 6 LED 18w 1500lm on OEM style dash switch -Body Mount Chop; cut, weld, paint -Fender mount chop, re-weld, paint -Fender Liner cut behind wheel (I cut liner in front of wheel clean off at top of viper cut) -Wheel well firewall hammering, painting ^done by Arc One Industries^ -valance cap trim -Agency6 Black Shackle Block 2" US Certified 6061 T6 CNC machined aluminum -DRT fab universal hitch skid -ACDelco inner tie rods, outer tie rods, bellows -Full Dr. KDSS switch kit -March 31 Behind grille 13-1/4" 32 LED light bar + wide-angle, eagle-eye lens 6000lm on OEM style dash switch -RAA Powder coated steel roof rack cargo basket, 1" side rails, 64" x 39" x 6", 250lb limit -roof gas can, water can, shovel -PEAKTOW PTT0063 Hitch Mount Cargo Carrier 51-1/2 x 17-1/2 x 4 inches 500 lbs. Capacity (trips only) -July/2023: purchased first needed SPC balljoint replacement kit - newly released, upgraded non-zerk sealed joints 25002 -July 15/2023: The Original Universal EZ Flares, 1". All four corners -Dec. 2023: removed bumper cover and crash bar, drilled frame, installed Apex Overland KDSS Recovery Points -Jan. 2024: SPC balljoint replacement kit - upgraded non-zerk sealed joint design 25002 -Jan. 2024: custom installed 2lb fire extinguisher between drivers seat and door -Feb. 2024: swapped interior lighting to diode dynamics led’s -Feb. 3/ 2024: 4x KC Wire Hiders, for roof rack lighting -Feb. 13/2024: double ditch lights, on new Rago Fabrication Extension brackets. -3inch Quad Row Amber Pods from LED-Club. 32W 3200Lm 16-LED Spot Beam. Existing: 3inch EVERGEAR clear lens LED pods -May 2024: custom black aluminum grille mesh installed in front of factory plastic -June 2024: custom built powder coated dom sliders -Nov. 2024: thermo-plastic rear mudflaps -Dec. 2024: rear bumper cover clearance cut, sprayed newly exposed parts black -Jan. 2025: trailer hitch removal, relocation of rear led pods to crossmember New: -Exhaust pipe chop after axle -March 2025: new SPC upper control arms, bushings, balljoints. Raised front end 0.75” via Bilstein 5100 spring seat. -April 2025: Evergear bezel-less cube ditch lights 4 LEDs 40W 3.33A 4800Lm 328’ beam distance 30° 6000k beam angle shatter & crack resistant lens -April 2025: Evergear Ultra Series light bar 27-3/4” flood spot combo 60 LEDs 60W 5A 6000Lm 1227’ beam distance Dual row, dual beam angle 30°/60° April 2025: BULLY Rock Crawler Hi-Intensity LED Utility Lights, Pair 1260 lumens @ 15w (3 x 5w CREE) each 120° flood beam waterproof, dustproof. Under hood: -Blue Fire 6-Circuit Fuse Block w/ LED Indicator & Protection Cover -Blue Sea 100A Circuit Breaker w/ reset lever In progress/in the garage queue: ~ Wanted - 80% OFFROAD Hitch Replacement Recovery Point, PerryParts or Wheelers bump stops, 1" body lift, custom dom front bumper, winch, rear dom bumper with side hoops, kdss angle correction, C or D load 35’s, bolt on cat shields
    IMG_20230331_220930984_Original.jpg


    Plus additional switches for roof rack scene lights (4) and rear roof rack chase light.

    IMG_9765.jpg
    IMG_0719.jpg
     
  17. Oct 22, 2025 at 5:22 PM
    #17
    GrantM64

    GrantM64 New Member

    Joined:
    Jun 7, 2022
    Member:
    #27390
    Messages:
    72
    Gender:
    Male
    All run from SwitchPro.

    upload_2025-10-22_17-21-43.png

    upload_2025-10-22_17-22-15.png
     
    Gman2530 and Rocket-67 like this.
  18. Oct 22, 2025 at 5:41 PM
    #18
    djwantke

    djwantke New Member

    Joined:
    Jan 31, 2021
    Member:
    #19487
    Messages:
    5,357
    Gender:
    Male
    Maple Ridge, British Columbia
    Vehicle:
    2016 4Runner Trail Premium
    Bought brand new 2016 After May 2021: -Approx 3" lift/level: Bilstein 5100's, OME 2884 590lb 3" front lift springs, SPC UCA's, ICON 158506 2" lift rear coils, diff drop -Mickey Thompson Baja ATZ LT285/70R17 Load E -Mickey Thompson Sidebiter ll 17x9, 0 offset, 5 backspace -Pro Comp black spline lugs ^installed by 4WheelParts^ -New brakes and rotors by brake shop -4-piece ARB skid kit -Smittybilt 2" nerf steps -MBRP black exhaust tip, chopped OEM -Drivers side OEM FJ oh shit handle -All blacked out emblems -Blacked out roof rails -4x WeatherTech window rain guards -OEM custom rear mud flap deletes -KICK BACK MUD FLAPS 12" WIDE - BLACK TOP AND BLACK WEIGHT -FRAM EXTRA GUARD CA10835 engine air filter -1797 LED tricolor fog bulbs Yellow 3000K White 6000K Blue 15000K 28W 4000LM -Armour paint lower rear bumper -Front bumper high stage high clearance cut -Fenders cut straight across, pink reservoir sprayed black -4Runner Lifestyle sequential fog fangs -4Runner Lifestyle smoked taillight decals -Pedal Commander -Rear passenger cargo mounted 120v truck tire pump -4x Spidertrax 1.25" black aluminum wheel spacers -Yota Twins Paracord Hatch Strap sand camo -Teton Workshop hard anodized matte black aluminum shift knob -Ditch flood lights 4 LED 20w 1400lm w/ OEM hood mounts on OEM style dash switch -Backup flood lights under bumper 6 LED 18w 1500lm on OEM style dash switch -Body Mount Chop; cut, weld, paint -Fender mount chop, re-weld, paint -Fender Liner cut behind wheel (I cut liner in front of wheel clean off at top of viper cut) -Wheel well firewall hammering, painting ^done by Arc One Industries^ -valance cap trim -Agency6 Black Shackle Block 2" US Certified 6061 T6 CNC machined aluminum -DRT fab universal hitch skid -ACDelco inner tie rods, outer tie rods, bellows -Full Dr. KDSS switch kit -March 31 Behind grille 13-1/4" 32 LED light bar + wide-angle, eagle-eye lens 6000lm on OEM style dash switch -RAA Powder coated steel roof rack cargo basket, 1" side rails, 64" x 39" x 6", 250lb limit -roof gas can, water can, shovel -PEAKTOW PTT0063 Hitch Mount Cargo Carrier 51-1/2 x 17-1/2 x 4 inches 500 lbs. Capacity (trips only) -July/2023: purchased first needed SPC balljoint replacement kit - newly released, upgraded non-zerk sealed joints 25002 -July 15/2023: The Original Universal EZ Flares, 1". All four corners -Dec. 2023: removed bumper cover and crash bar, drilled frame, installed Apex Overland KDSS Recovery Points -Jan. 2024: SPC balljoint replacement kit - upgraded non-zerk sealed joint design 25002 -Jan. 2024: custom installed 2lb fire extinguisher between drivers seat and door -Feb. 2024: swapped interior lighting to diode dynamics led’s -Feb. 3/ 2024: 4x KC Wire Hiders, for roof rack lighting -Feb. 13/2024: double ditch lights, on new Rago Fabrication Extension brackets. -3inch Quad Row Amber Pods from LED-Club. 32W 3200Lm 16-LED Spot Beam. Existing: 3inch EVERGEAR clear lens LED pods -May 2024: custom black aluminum grille mesh installed in front of factory plastic -June 2024: custom built powder coated dom sliders -Nov. 2024: thermo-plastic rear mudflaps -Dec. 2024: rear bumper cover clearance cut, sprayed newly exposed parts black -Jan. 2025: trailer hitch removal, relocation of rear led pods to crossmember New: -Exhaust pipe chop after axle -March 2025: new SPC upper control arms, bushings, balljoints. Raised front end 0.75” via Bilstein 5100 spring seat. -April 2025: Evergear bezel-less cube ditch lights 4 LEDs 40W 3.33A 4800Lm 328’ beam distance 30° 6000k beam angle shatter & crack resistant lens -April 2025: Evergear Ultra Series light bar 27-3/4” flood spot combo 60 LEDs 60W 5A 6000Lm 1227’ beam distance Dual row, dual beam angle 30°/60° April 2025: BULLY Rock Crawler Hi-Intensity LED Utility Lights, Pair 1260 lumens @ 15w (3 x 5w CREE) each 120° flood beam waterproof, dustproof. Under hood: -Blue Fire 6-Circuit Fuse Block w/ LED Indicator & Protection Cover -Blue Sea 100A Circuit Breaker w/ reset lever In progress/in the garage queue: ~ Wanted - 80% OFFROAD Hitch Replacement Recovery Point, PerryParts or Wheelers bump stops, 1" body lift, custom dom front bumper, winch, rear dom bumper with side hoops, kdss angle correction, C or D load 35’s, bolt on cat shields
    Nice

    Where you opt to mount the switch pro?
    above the factory switches or up at the headliner switches
     
  19. Oct 22, 2025 at 5:45 PM
    #19
    GrantM64

    GrantM64 New Member

    Joined:
    Jun 7, 2022
    Member:
    #27390
    Messages:
    72
    Gender:
    Male
    Above the factory switches. Wiring it up was very easy.
     
    Rocket-67 and djwantke[QUOTED] like this.
  20. Oct 23, 2025 at 9:00 AM
    #20
    TroutMan

    TroutMan New Member

    Joined:
    Apr 3, 2024
    Member:
    #39591
    Messages:
    81
    @surfingbuddhist how did you get power to the lights on the roof rack? I'd like some side lights but I've not come up with a creative solution.
     
  21. Oct 23, 2025 at 10:52 AM
    #21
    DriftingOverland

    DriftingOverland Just a guy and his 4Runner

    Joined:
    Sep 4, 2025
    Member:
    #48853
    Messages:
    39
    Vehicle:
    2020 Silver TRD ORP
    Vehicle Mods: A Lot.
    No pictures at night (Got to change that) All of mine run through the SP9100 (mounted in the small center console cubby) and looks very similar to surfingbuddist when they are on::cool:
    • Headlights - Xenon Depot LEDs
    • Fog lights - Yellow Diode Dynamic SS3 Kit
    • 40” light bar by Extreme LED
    • 30” bar by Extreme LED in winch/front bumper with Lamin-x yellow film
    • Enhanced LED puddle lights
    • Ditch lights- Baja Designs S2s w/Cali Raised brackets
    • Sylvania flush LEDs rack mounted lights with Lamin-x yellow film
    • Rock lights HID Kit Pros
    • Yellow Diode Dynamic SS3-Rear bumper
    • Rear Chase lights (Amazon) with Lamin-x yellow film
     
    Last edited: Oct 23, 2025
    Laith027[OP] and Rocket-67 like this.
  22. Oct 23, 2025 at 11:01 AM
    #22
    DriftingOverland

    DriftingOverland Just a guy and his 4Runner

    Joined:
    Sep 4, 2025
    Member:
    #48853
    Messages:
    39
    Vehicle:
    2020 Silver TRD ORP
    Vehicle Mods: A Lot.
    I ran all my roof light cabling down the “rain channel” on each side of my windshield. You can also buy cable hiders specifically for that purpose.

    https://www.amazon.com/dp/B0D8BFRZBF
     
    Last edited: Oct 23, 2025
    Rocket-67 and TroutMan[QUOTED] like this.
  23. Oct 23, 2025 at 11:37 AM
    #23
    Ripper238

    Ripper238 New Member

    Joined:
    Jan 21, 2023
    Member:
    #30792
    Messages:
    1,384
    Gender:
    Male
    Vehicle:
    2019 TRD OR
    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]

    Also split my fogs, white on bottom for better color visibility and yellow up top to cut through fog.
    [​IMG]
     
  24. Oct 23, 2025 at 4:10 PM
    #24
    4RunRap556

    4RunRap556 New Member

    Joined:
    Aug 19, 2025
    Member:
    #48594
    Messages:
    45
    Gender:
    Male
    Way up in New England
    Vehicle:
    2020 4r sr5 silver
    None yet
    Going with diodes yellow fogs, white spots for ditch(maybe), and a single combo in hitch for reverse lighting. Keeping it simple since this isnt the main offroad vehicle.
     
    Rocket-67 likes this.
  25. Oct 23, 2025 at 5:24 PM
    #25
    Captain Spalding

    Captain Spalding . . .

    Joined:
    Feb 4, 2022
    Member:
    #25492
    Messages:
    2,792
    Hey Crow. Nice parking job. ;-)
     
  26. Oct 23, 2025 at 5:57 PM
    #26
    Henry J

    Henry J Crap…crap crap crap crap…crap

    Joined:
    Aug 8, 2020
    Member:
    #15986
    Messages:
    895
    Gender:
    Male
    Sacramento Ca
    Vehicle:
    2008 Brick Red FJ & 2011 Silver T4R Trail
    DD Ambers all around
    SS3 pro fog and ditch lights
    SS5 pro in the grillle
    SS5 sport (cause damn $$) crosslink
    SSC2 pro chase lights

    DD rock lights (8)

    IMG_3564.jpg
    IMG_3053.jpg
     
  27. Oct 23, 2025 at 9:22 PM
    #27
    djwantke

    djwantke New Member

    Joined:
    Jan 31, 2021
    Member:
    #19487
    Messages:
    5,357
    Gender:
    Male
    Maple Ridge, British Columbia
    Vehicle:
    2016 4Runner Trail Premium
    Bought brand new 2016 After May 2021: -Approx 3" lift/level: Bilstein 5100's, OME 2884 590lb 3" front lift springs, SPC UCA's, ICON 158506 2" lift rear coils, diff drop -Mickey Thompson Baja ATZ LT285/70R17 Load E -Mickey Thompson Sidebiter ll 17x9, 0 offset, 5 backspace -Pro Comp black spline lugs ^installed by 4WheelParts^ -New brakes and rotors by brake shop -4-piece ARB skid kit -Smittybilt 2" nerf steps -MBRP black exhaust tip, chopped OEM -Drivers side OEM FJ oh shit handle -All blacked out emblems -Blacked out roof rails -4x WeatherTech window rain guards -OEM custom rear mud flap deletes -KICK BACK MUD FLAPS 12" WIDE - BLACK TOP AND BLACK WEIGHT -FRAM EXTRA GUARD CA10835 engine air filter -1797 LED tricolor fog bulbs Yellow 3000K White 6000K Blue 15000K 28W 4000LM -Armour paint lower rear bumper -Front bumper high stage high clearance cut -Fenders cut straight across, pink reservoir sprayed black -4Runner Lifestyle sequential fog fangs -4Runner Lifestyle smoked taillight decals -Pedal Commander -Rear passenger cargo mounted 120v truck tire pump -4x Spidertrax 1.25" black aluminum wheel spacers -Yota Twins Paracord Hatch Strap sand camo -Teton Workshop hard anodized matte black aluminum shift knob -Ditch flood lights 4 LED 20w 1400lm w/ OEM hood mounts on OEM style dash switch -Backup flood lights under bumper 6 LED 18w 1500lm on OEM style dash switch -Body Mount Chop; cut, weld, paint -Fender mount chop, re-weld, paint -Fender Liner cut behind wheel (I cut liner in front of wheel clean off at top of viper cut) -Wheel well firewall hammering, painting ^done by Arc One Industries^ -valance cap trim -Agency6 Black Shackle Block 2" US Certified 6061 T6 CNC machined aluminum -DRT fab universal hitch skid -ACDelco inner tie rods, outer tie rods, bellows -Full Dr. KDSS switch kit -March 31 Behind grille 13-1/4" 32 LED light bar + wide-angle, eagle-eye lens 6000lm on OEM style dash switch -RAA Powder coated steel roof rack cargo basket, 1" side rails, 64" x 39" x 6", 250lb limit -roof gas can, water can, shovel -PEAKTOW PTT0063 Hitch Mount Cargo Carrier 51-1/2 x 17-1/2 x 4 inches 500 lbs. Capacity (trips only) -July/2023: purchased first needed SPC balljoint replacement kit - newly released, upgraded non-zerk sealed joints 25002 -July 15/2023: The Original Universal EZ Flares, 1". All four corners -Dec. 2023: removed bumper cover and crash bar, drilled frame, installed Apex Overland KDSS Recovery Points -Jan. 2024: SPC balljoint replacement kit - upgraded non-zerk sealed joint design 25002 -Jan. 2024: custom installed 2lb fire extinguisher between drivers seat and door -Feb. 2024: swapped interior lighting to diode dynamics led’s -Feb. 3/ 2024: 4x KC Wire Hiders, for roof rack lighting -Feb. 13/2024: double ditch lights, on new Rago Fabrication Extension brackets. -3inch Quad Row Amber Pods from LED-Club. 32W 3200Lm 16-LED Spot Beam. Existing: 3inch EVERGEAR clear lens LED pods -May 2024: custom black aluminum grille mesh installed in front of factory plastic -June 2024: custom built powder coated dom sliders -Nov. 2024: thermo-plastic rear mudflaps -Dec. 2024: rear bumper cover clearance cut, sprayed newly exposed parts black -Jan. 2025: trailer hitch removal, relocation of rear led pods to crossmember New: -Exhaust pipe chop after axle -March 2025: new SPC upper control arms, bushings, balljoints. Raised front end 0.75” via Bilstein 5100 spring seat. -April 2025: Evergear bezel-less cube ditch lights 4 LEDs 40W 3.33A 4800Lm 328’ beam distance 30° 6000k beam angle shatter & crack resistant lens -April 2025: Evergear Ultra Series light bar 27-3/4” flood spot combo 60 LEDs 60W 5A 6000Lm 1227’ beam distance Dual row, dual beam angle 30°/60° April 2025: BULLY Rock Crawler Hi-Intensity LED Utility Lights, Pair 1260 lumens @ 15w (3 x 5w CREE) each 120° flood beam waterproof, dustproof. Under hood: -Blue Fire 6-Circuit Fuse Block w/ LED Indicator & Protection Cover -Blue Sea 100A Circuit Breaker w/ reset lever In progress/in the garage queue: ~ Wanted - 80% OFFROAD Hitch Replacement Recovery Point, PerryParts or Wheelers bump stops, 1" body lift, custom dom front bumper, winch, rear dom bumper with side hoops, kdss angle correction, C or D load 35’s, bolt on cat shields
    :spending::spending::spending:
     
    Gman2530, Thacrow and Rocket-67 like this.
  28. Oct 23, 2025 at 11:06 PM
    #28
    Henry J

    Henry J Crap…crap crap crap crap…crap

    Joined:
    Aug 8, 2020
    Member:
    #15986
    Messages:
    895
    Gender:
    Male
    Sacramento Ca
    Vehicle:
    2008 Brick Red FJ & 2011 Silver T4R Trail
    Amazon gifts cards:yes:
     
  29. Oct 24, 2025 at 12:23 AM
    #29
    Thacrow

    Thacrow New Member

    Joined:
    May 30, 2021
    Member:
    #21719
    Messages:
    1,923
    Gender:
    Male
    NorCal
    Vehicle:
    2021 ORP
    Speed holes
    I start doing that when I haven't been off road recently:)
     
  30. Oct 24, 2025 at 3:19 AM
    #30
    Steely123

    Steely123 What's the new trend? I'll do it!

    Joined:
    Jun 4, 2022
    Member:
    #27323
    Messages:
    7,786
    Gender:
    Male
    TX
    Vehicle:
    2018 4runner SR5 premium
    Off road, suuuuure.
     
    Thatbassguy and Thacrow[QUOTED] like this.
To Top