1. Welcome to 4Runners.com!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all 4Runner discussion topics
    • Transfer over your build thread from a different forum to this one
    • Communicate privately with other 4Runner owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

Suspension

Discussion in '3rd Gen 4Runners (1996-2002)' started by Dylanmnt, Jul 9, 2025.

  1. Jul 9, 2025 at 3:39 PM
    #1
    Dylanmnt

    Dylanmnt [OP] New Member

    Joined:
    Jun 8, 2025
    Member:
    #47485
    Messages:
    6
    First Name:
    Dylan
    Vehicle:
    2000 4runner
    Does anyone know if I can run bilstein 6112 front with bilsteins 5100 long travel in the rear with ome 831 springs in the rear?
     
  2. Jul 10, 2025 at 5:04 AM
    #2
    roboturner

    roboturner Dead Eyed

    Joined:
    Nov 4, 2022
    Member:
    #29416
    Messages:
    267
    Colorado
    Vehicle:
    ‘98 NW 3.4L 5MT SR5 | '18 6MT DCSB Tacoma | '00 IJM 3.4L TRD Tacoma
    You should add all your suspension questions into one thread, that being said-

    If you mean extended travel vs a true long travel kit, Yes either work, I don’t know about OME 831, but below are the common OME springs that work for the 3rd gen (2890 is 890 etc). I’ve had both the 5100s and the 6112/5160s - I like the 6112 better but if you don’t off-road, they’re overkill. I use 2891s with a steel rear swing out and have maintained my ~2” lift.

    Front Coil Springs
    • OME 880
      • Lift: ~1.75”
      • Load Rating: Light load
      • Supports: 0–110 lbs additional front weight
    • OME 881
      • Lift: ~2.0”
      • Load Rating: Medium load
      • Supports: 110–200 lbs (e.g., light bumper, small winch)
    • OME 882
      • Lift: ~2.5”
      • Load Rating: Heavy load
      • Supports: 200–300 lbs (e.g., steel bumper, winch)
    • OME 883
      • Lift: ~3.0”
      • Load Rating: Extra heavy load
      • Supports: 300+ lbs (e.g., bumper, winch, dual batteries, skid plates)

      Rear Coil Springs (OME)
      • OME 890
        • Lift: ~2.0”
        • Load Rating: Light load
        • Supports: 0–200 lbs rear cargo or constant load
      • OME 891
        • Lift: ~2.5”
        • Load Rating: Medium load
        • Supports: 200–400 lbs (light camping gear, drawer system)
      • OME 892
        • Lift: ~3.0”
        • Load Rating: Heavy load
        • Supports: 400+ lbs (overlanding gear, bumper, roof rack, drawers)
     
  3. Jul 10, 2025 at 2:14 PM
    #3
    Dylanmnt

    Dylanmnt [OP] New Member

    Joined:
    Jun 8, 2025
    Member:
    #47485
    Messages:
    6
    First Name:
    Dylan
    Vehicle:
    2000 4runner
    Thanks, so when you had the 6112/5160 on, were you running the 861 spring in the rear? And also do you think the 6112/5160 give you enough hight for off-roading?
     
  4. Jul 11, 2025 at 6:14 AM
    #4
    roboturner

    roboturner Dead Eyed

    Joined:
    Nov 4, 2022
    Member:
    #29416
    Messages:
    267
    Colorado
    Vehicle:
    ‘98 NW 3.4L 5MT SR5 | '18 6MT DCSB Tacoma | '00 IJM 3.4L TRD Tacoma
    The 5160 and 5100 are the same length, the 5160 just has a remote reservoir and is a little thicker. The shocks don’t influence lift, the springs do. In this case I use the 2891 (“891”) springs because I have a steel bumper (extra weight) - I maintain 2” which is enough ground clearance for what I do. The IFS these Toyotas have doesnt do well with anything over 2.5-3” lift. 2” is really your sweet spot.
     

Products Discussed in

To Top