Show your T4R with wheel spacers on stock wheels!

show your rig on stock wheels and tires with wheel spacers, weather lifted or non lifted

thanks!

 

Spidertrax 285/70/17 Nitto Ridge Grapplers

 

Same as above

 

1.25” Spidertrax, Bilstein 5100 at .85, and 265/70r17 Wildpeak AT3Ws.

 

Ohh... I have a stock TDORP, today I'm getting 275/70/17 AT KO2's installed... I wonder if a .75 or 1.00 spacer would work.

 

Hi there... so you have 33s on that that truck with no lift? only spider trax??? I have a pro and I have a burtman spacers, 1" front and 1/2" rear that I haven't installed yet, I was going to trade them in and get 2" front and 1" rear to get 33s and probably get spider trax. I don't want to trim anything.... what exactly do you have on there and did you have to trim anything? any rubbing? looks great! TY!

 

looks like he has a lift. Depending on the tire 285’a are gonna rub your bumper and body mount. Most definitely will with spacers.

 

Thank you....so it almost seems to me from what I am reading that on my TRD PRO with stock wheels, no matter what combination of lift and spidertrax I will have to trim, btw they would be BFG Ta ko2 285s. I really don't want to trim, I just want a little more aggressive stance. Sounds like even pushing the stock tires/wheels out with spidertrax will cause rubbing? geez I need a chart

 

1.25” spidertraxx, 285/70 KO2’s, Westcott lift. Had to remove mudflaps, fender liner mod, and about an inch and a half of the bumper

 

When I had the stock 265 terra grapplers and 1.25 spacers it was hitting the fender liner. At the very least you would just need to push the liner forward with 1" spacers and 275s. Even with my spacers and 285s I don't rub the body mounts ( i did remove the mudlaps, however)

 

there is a chart out there, but it’s not that accurate IMO.

Trimming the bumper looks great and it’s easy to do. Adding spacers you may need to have a body mount chop done - ko2’s are a little bit smaller than other 285’a so maybe not be an issue.

 

does ANYONE on here have PRO wheels with 275s with spacers (1"or 1.25') with no rubbing? that may be a simpler solution than 285s if anyone has done it successfully with no mods, I would love to see/hear about it....Thank you for the imput

 

I did the a billstein lift with 280 KO2 and I had to remove mudflaps and trim. Trimming seems pretty inevitable.

 

No one can guarantee you it won't rub for sure. You just have to try it and be ok with a little trimming if you do rub. Trimming isn't as big of a deal as it sounds.

You have the best chance of not rubbing with your PRO because it already has the fender liner moved forward and the bumper trimmed from the factory.

One trick you can use if you find that you rub on the mudflap or body mount near the rear of your fender well is having the caster adjusted during an alignment. You'll want to ask your alignment shop to push the caster as far forward as they can. With a stock Pro, that would be somewhere close to +3.8 degrees or so.

In order to get those caster numbers with the lift you plan to put on, you'll need aftermarket Upper Control Arms.

 

Running Cooper Evo MT's, 285/70/17 on stock OR wheels with spidertrax 1.25" spacers. I have a Bilstein 6112/5160 3" lift with JBA UCA's. I had to remove the mud flaps, trim the bumper and do a BMC to eliminate all rubbing.

 

I love your front bumper trim! Is that rubber trim on the edge or was that some sort of a kit? I've been leaning towards a viper cut on mine but most examples don't go vertical at the bottom like yours does. Looks sweet.

 

thanks, you can find the trim here. Just use painters tape to line out what you like

TRIM-LOK Edge Trim – Fits 1/16” Edge, 9/16” Leg Length, 25’ Length, Black, Pebble Texture – Flexible PVC Edge Protector for Sharp/Rough Surfaces, Easy to Install

$47 TRIM-LOK Edge Trim – Fits 1/16” Edge, 9/16” Leg Length, 25’ Length, Black, Pebble Texture – Flexible PVC Edge Protector for Sharp/Rough Surfaces, Easy to Install

https://www.amazon.com/dp/B00NL3YN7O?_encoding=UTF8

 

Do you happen to have the viper trim layout measurements? I'm highly considering it. Thanks

 

Do you have any lift on this?

 

I’m currently going for the same setup in my 5th gen 4Runner, did you have any rub back then?