1. Welcome to 4Runners.com!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all 4Runner discussion topics
    • Transfer over your build thread from a different forum to this one
    • Communicate privately with other 4Runner owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

Help identifying a part

Discussion in '2nd Gen 4Runners (1990-1995)' started by rhinolined, Mar 4, 2019.

  1. Mar 4, 2019 at 3:51 PM
    #1
    rhinolined

    rhinolined [OP] New Member

    Joined:
    Feb 26, 2019
    Member:
    #8959
    Messages:
    56
    Gender:
    Male
    First Name:
    Andrew
    Vehicle:
    1991 4Runner 3VZ-E 4x4 5-Speed
    Ok Gents (and Gals if there in here) need help identifying what this is. Looks to be a sensor of sorts but the old motor didn't have it and I have no way of hooking it up. Below is the picture of the culprit and a picture of where I pulled it from. From what I can tell before i took off the intake and started working on it the check engine light wasn't on when it first starts and then would come on when the engine was revved up which would cause the timing to get out because of a bad hydraulic tensioner (I believe this caused the check engine light and has nothing to do with the below sensor)

    Unk Sensor

    Spot i pulled the sensor from

    so in the end if someone can identify it do i need it or can i just put it back in to plug the hole and go on my way?
     
  2. Mar 4, 2019 at 5:04 PM
    #2
    HoBoDanny

    HoBoDanny Dude...

    Joined:
    Feb 5, 2019
    Member:
    #8697
    Messages:
    966
    Gender:
    Male
    First Name:
    Daniel
    Kentucky
    Vehicle:
    2004 SR5 V6 4WD 4Runner
    RCI Skid Plate CBI Ditch Light Brackets Hankook DynaPro ATM RF10 265 70R17 113T Tires 1.25” Wheel Spacers TPMS Bypass Mod Hydrocarbon Filter Removed Merca decal 2” leveling kit front only Black headlights
    Definitely a temp sensor of some sort but looks like the top of it may be missing a part.
     
  3. Mar 4, 2019 at 6:33 PM
    #3
    Kyle11863

    Kyle11863 King of the BS

    Joined:
    Jul 28, 2015
    Member:
    #807
    Messages:
    252
    Gender:
    Male
    First Name:
    Kyle
    Big Bear California
    Vehicle:
    1990 Toyota 4Runner SR5 V6 5 Speed Manual
    Doug Thorley long tube headers and lots of mud
    Plug all your sensors in that you can. There should be a wire that doesn’t have a mate. Go to your old engine and find the one that matches, (usually color coded to match) and see if it fits in the hole. If not just take that whole sensor bank off of the old engine and put it on the new engine.

    Different year engines had different sensors so swapping over could make it run rough as not all sensors and ecu’s are compatible. Luckily the sensor banks fit any 3.0 engine so if you don’t have the correct one and the old engine is gone you could always go to the junkyard and find an engine from the same year and take its sensor bank. That’s usually the easiest way because there are so many different sensors that got used and figureing them out is a pain.
     
  4. Mar 4, 2019 at 7:31 PM
    #4
    rhinolined

    rhinolined [OP] New Member

    Joined:
    Feb 26, 2019
    Member:
    #8959
    Messages:
    56
    Gender:
    Male
    First Name:
    Andrew
    Vehicle:
    1991 4Runner 3VZ-E 4x4 5-Speed
    Thanks for the input, old motor was turned in for core charge, any broken sensors on the new engine were replaced with sensors from the old engine that were good. All wires on harness are plugged in and there simply is no extra wire for this sensor. still have to put the intake back on tomorrow and start it back up, for now i put the sensor back in due to not wanting to leave a hole; however, when it was running before redoing the timing belt it was running fine until giving it throttle which was because once it got throttle it would go out of time by 36 degrees :eek: so i am going with the theory that the hydraulic was out and as soon as throttle was put on the cam would slip and knock it out of time.


    will update once i get it put back together and get the timing tweaked.
     
  5. Mar 4, 2019 at 7:39 PM
    #5
    Kyle11863

    Kyle11863 King of the BS

    Joined:
    Jul 28, 2015
    Member:
    #807
    Messages:
    252
    Gender:
    Male
    First Name:
    Kyle
    Big Bear California
    Vehicle:
    1990 Toyota 4Runner SR5 V6 5 Speed Manual
    Doug Thorley long tube headers and lots of mud
    Hmm interesting. Sounds like you might have a 4 sensor truck with a 5 sensor engine. Somewhere between 90 and 95 they went from 5 to 4. They also moved the heater hose from the intake plenum to that sensor bank to replace that 5th sensor. If that’s the case you probably don’t need to worry about it if its running fine other than the timing. That definitely sounds like something in the timing belt isn’t right. What I normally do is I’ll line up all the marks, set the tentioner and rotate it through 2-3 times. If the marks all line up I’ll start it up real quick with the timing belt still exposed and rev it up a bit to make sure. That way if you’re a tooth off or the tentioner isn’t right you can tell immediately and readjust. Just don’t do it for long as you won’t have coolant circulation. As long as the engine remains cold it won’t hurt anything
     
  6. Mar 4, 2019 at 7:44 PM
    #6
    rhinolined

    rhinolined [OP] New Member

    Joined:
    Feb 26, 2019
    Member:
    #8959
    Messages:
    56
    Gender:
    Male
    First Name:
    Andrew
    Vehicle:
    1991 4Runner 3VZ-E 4x4 5-Speed
    yea that makes sense the old motor was a 91, new one is somewhere between 93-95 (this was determined through research because old engine had a tensioner spring (88-92 i believe) and the new one has a hydraulic tensioner (93-95 i believe) so im pretty happy due to newer engine should mean less miles since the salvage yard i got it from had no info on the motor lol

    What i know about the new motor
    Came out of an automatic (had to change the flywheel)
    Came out of a 2wd vehicle (had to change the oil pan due to it hitting the front diff)
    Newer motor due to having a hydraulic tensioner
    possibly came from a truck because i left the old motor mounts on it and it sits higher and closer to the firewall (i have my old motor mounts and will one day lift the motor and swap them so it sits more comfortable but for now there is no serious issues as the hood clears and its closer but not too close to the firewall)
     

Products Discussed in

To Top