1. Welcome to 4Runners.com!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all 4Runner discussion topics
    • Transfer over your build thread from a different forum to this one
    • Communicate privately with other 4Runner owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

Brake drum drag metal to metal

Discussion in '3rd Gen 4Runners (1996-2002)' started by ktoelke, Jun 4, 2017.

  1. Jun 4, 2017 at 11:20 AM
    #1
    ktoelke

    ktoelke [OP] New Member

    Joined:
    Jun 4, 2017
    Member:
    #4144
    Messages:
    3
    Gender:
    Male
    Noticed metal to metal drag sound from rear drum. Just had axle bearing seal and break job done recently. Disassembled and inspected and found where the noise originated. Now looking for cause? IMG_0224.jpgFullSizeRender.jpg
     
  2. Jun 4, 2017 at 12:02 PM
    #2
    jtdashark

    jtdashark New Member

    Joined:
    Apr 3, 2017
    Member:
    #3822
    Messages:
    21
    Gender:
    Male
    First Name:
    Jim
    Vehicle:
    2000 Toyota 4Runner
    N/A
    Time to get them possibly resurfaced or purchased a new set of drums
     
  3. Jun 4, 2017 at 12:13 PM
    #3
    ktoelke

    ktoelke [OP] New Member

    Joined:
    Jun 4, 2017
    Member:
    #4144
    Messages:
    3
    Gender:
    Male
    Pads are new, drums were turned, surface nice and smooth. The drag is between the outer groove on the drum and the inner flange of the plate the brake hardware mounts to. (See Photos) These parts nest inside each other but are not meant to touch. I've lost clearance. Not sure how? Thanks.
     
  4. Jun 4, 2017 at 12:16 PM
    #4
    jtdashark

    jtdashark New Member

    Joined:
    Apr 3, 2017
    Member:
    #3822
    Messages:
    21
    Gender:
    Male
    First Name:
    Jim
    Vehicle:
    2000 Toyota 4Runner
    N/A
    Have you reset your space between the drum and shoes when you crank that thread ( not sure what's it called)
     
  5. Jun 4, 2017 at 12:38 PM
    #5
    ktoelke

    ktoelke [OP] New Member

    Joined:
    Jun 4, 2017
    Member:
    #4144
    Messages:
    3
    Gender:
    Male
    Yes, that's what I first thought, that I had an issue between the drum and shoes. But when I inspected, I found the evidence of metal to metal between the drum and the non-rotating plate that all the brake components are mounted to. So best I can figure I've some how lost clearance. I was wondering if the recently installed bearing could have something to do with it, if it weren't pressed to the proper position on the shaft. Could this be where I lost my clearance?
     
  6. Jun 4, 2017 at 12:45 PM
    #6
    jtdashark

    jtdashark New Member

    Joined:
    Apr 3, 2017
    Member:
    #3822
    Messages:
    21
    Gender:
    Male
    First Name:
    Jim
    Vehicle:
    2000 Toyota 4Runner
    N/A
    The best I would I do is disassemble it, inspect the parts, lube whatever parts and reassemble it back again
     
  7. Sep 5, 2017 at 2:54 PM
    #7
    TN_TRAIL

    TN_TRAIL New Member

    Joined:
    Dec 24, 2016
    Member:
    #3237
    Messages:
    106
    Gender:
    Male
    First Name:
    Noel
    Vehicle:
    2017 TRD OFF RD PREM
    oh the list....!
    I wonder if there might be one of two possibilities going on here. First, since the bearing seal was replaced, I am thinking that the c-clip that holds the axle on may not be fully seated in its recess. (This is bad) The c-clip might be slightly bent, which could be still holding the axle on.... (I'd check that NOW!!) Second, just to make sure something goofy isn't going on with the drum, I would compare the clearance with the other side's drum. C-clip yikes!!!
     
  8. Mar 8, 2018 at 10:11 AM
    #8
    Mountain Top

    Mountain Top New Member

    Joined:
    Mar 5, 2018
    Member:
    #5607
    Messages:
    7
    Gender:
    Male
    First Name:
    steve
    Vehicle:
    1999 Toyota 4Runner 2WD Limited
    It looks like you have a wobble in the brake drum.
    Is it on one side only?
    I would make sure that the surfaces where the drum and the axle mate are thoroughly clean, and that the drum sits nice and flush when you slide it on the axle.
    Also, be sure to torque your lug nuts in from side to side in a alternating sequence, and torque to specification.

    Hope this helps
     

Products Discussed in

To Top