1. Welcome to 4Runners.com!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all 4Runner discussion topics
    • Transfer over your build thread from a different forum to this one
    • Communicate privately with other 4Runner owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

Lean Correction - Strange Results

Discussion in '5th Gen 4Runners (2010-2024)' started by TrueTexas, Sep 7, 2022.

  1. Sep 7, 2022 at 3:52 PM
    #1
    TrueTexas

    TrueTexas [OP] New Member

    Joined:
    Jun 1, 2021
    Member:
    #21753
    Messages:
    324
    Gender:
    Male
    The Woodlands, TX
    Vehicle:
    2021 Magnetic Grey 4Runner TRD ORP
    I recently added the rear 10mm OME spacer (the version that sits above the coil) to the rear drivers side to try to correct some of the lean. The results are not at all what I was expecting.

    • The rear drivers side did not lift at all. I was at 23-3/4" before and am still at 23-3/4"
    • The rear passenger side lifted 1/8"
    • The front drivers side came up 1/4"
    • The front passenger side came up 1/8"

    I now have 3/8" of lean in both the front and the rear.

    Couple of notes
    • This is with an empty tank (before and after), I will take measurements with a full tank (have the before measurements already). However, based on previous measurements, this is going to make the lean even worse.
    • I made sure the rear springs seated nicely in their cups and the spacer was in the right place as the spring compressed.
    • I measured with the same measuring tape from the bottom of the wheel well to center of wheel so tires are not a consideration.
    • I drove about 50 miles (including over speed bumps, rough terrain etc...) to get it to settle before measuring.

    Not sure if I am chasing a lean that doesn't "want" to be fixed. But I have ordered a Moto-fab 1/4" spacer from Amazon to install in the driver front to see if that corrects anything.

    I have read a couple of others who saw no change from a rear spacer. Did following up with a front shim, correct / improve the lean?
     
  2. Sep 7, 2022 at 3:56 PM
    #2
    Dillusion

    Dillusion New Member

    Joined:
    Dec 10, 2018
    Member:
    #7998
    Messages:
    2,687
    Gender:
    Male
    First Name:
    KYle
    Vehicle:
    2018 TRD OR
    Correct me if I'm wrong but don't you install a spacer in the front and rear?

    Also how are you measuring? Center of hub to fender?
     
  3. Sep 7, 2022 at 4:00 PM
    #3
    TrueTexas

    TrueTexas [OP] New Member

    Joined:
    Jun 1, 2021
    Member:
    #21753
    Messages:
    324
    Gender:
    Male
    The Woodlands, TX
    Vehicle:
    2021 Magnetic Grey 4Runner TRD ORP
    Based in my results, I am thinking you are not wrong @Dillusion

    I have ordered the front 1/4" spacer from Amazon. It's made from steel vs others that are aluminum or poly. Not sure if it's the best option. If not, let me know and I will order a different one.
     
  4. Sep 7, 2022 at 4:01 PM
    #4
    TrueTexas

    TrueTexas [OP] New Member

    Joined:
    Jun 1, 2021
    Member:
    #21753
    Messages:
    324
    Gender:
    Male
    The Woodlands, TX
    Vehicle:
    2021 Magnetic Grey 4Runner TRD ORP
    And yes, measuring center of hub to bottom of fender.

    Edit, actually the chamfer on the bottom of the fender as it provides a consistent reference line
     
  5. Sep 7, 2022 at 4:05 PM
    #5
    TrueTexas

    TrueTexas [OP] New Member

    Joined:
    Jun 1, 2021
    Member:
    #21753
    Messages:
    324
    Gender:
    Male
    The Woodlands, TX
    Vehicle:
    2021 Magnetic Grey 4Runner TRD ORP
  6. Sep 7, 2022 at 4:09 PM
    #6
    Dillusion

    Dillusion New Member

    Joined:
    Dec 10, 2018
    Member:
    #7998
    Messages:
    2,687
    Gender:
    Male
    First Name:
    KYle
    Vehicle:
    2018 TRD OR
    I just see 2 different spacers for lean for front and back so I'm just assuming you need both.

    Not sure why not just tell um together.
     
  7. Sep 7, 2022 at 4:15 PM
    #7
    TrueTexas

    TrueTexas [OP] New Member

    Joined:
    Jun 1, 2021
    Member:
    #21753
    Messages:
    324
    Gender:
    Male
    The Woodlands, TX
    Vehicle:
    2021 Magnetic Grey 4Runner TRD ORP
    That would be way to easy.

    I did just the rear first to see how much that would help. Turns out, the answer is "not at all"

    I'm just trying to figure out if I am going to be just as disappointed when I add the front spacer and it still isn't any better. Not looking for perfect, just looking for better than I was after the mild lift.

    BTW - no KDSS on mine
     
  8. Sep 7, 2022 at 4:18 PM
    #8
    TrueTexas

    TrueTexas [OP] New Member

    Joined:
    Jun 1, 2021
    Member:
    #21753
    Messages:
    324
    Gender:
    Male
    The Woodlands, TX
    Vehicle:
    2021 Magnetic Grey 4Runner TRD ORP
    for reference on the front spacer choices, here is what I came up with. Feel free to add or fill in the blanks


    List of ¼” front strut spacers


    Toytec TP-14 (Not sure if this even fits a 5th Gen 4Runner)

    Material: 6061 T6 Aluminum Dobinsons

    Material 6061 T6 Aluminum

    https://www.dobinsonsdirect.com/pro...-runner-5th-gen~yr_2010-2022-suspension-parts


    Wheelers OffRoad

    Material: Polyurethane or Aluminum options Note- Select Option for poly vs aluminum

    Shipping was a deal breaker $20.39 via US Postal Service


    Moto-Fab

    Material – Mild Steel

    https://www.amazon.com/MotoFab-Lift...=1662507740&sprefix=motofab+t,aps,2679&sr=8-1


    Cornfed

    Material – Unknown (please update)

    https://www.cornfedsuspension.com/driverssidesagcorrection/
     
    Basset_Dad likes this.
  9. Sep 7, 2022 at 4:54 PM
    #9
    TrueTexas

    TrueTexas [OP] New Member

    Joined:
    Jun 1, 2021
    Member:
    #21753
    Messages:
    324
    Gender:
    Male
    The Woodlands, TX
    Vehicle:
    2021 Magnetic Grey 4Runner TRD ORP
    2016 4Runner SR5 likes this.
  10. Sep 7, 2022 at 5:04 PM
    #10
    2016 4Runner SR5

    2016 4Runner SR5 CONTACT ME FOR CORNFED LIFT SPACERS 631-202-8245

    Joined:
    Jan 29, 2017
    Member:
    #3447
    Messages:
    1,076
    Gender:
    Male
    First Name:
    #Rensing Off-Road
    North Carolina
    UHMW and backed by a no questions asked lifetime warranty. For anyone in need of this specific spacer, cost is $20 including shipping anywhere in the US!

    If anyone is interested in ordering any other kit, including custom kits, please reach out to me. 631-202-8245
     
    Last edited: Sep 7, 2022
  11. Sep 7, 2022 at 5:10 PM
    #11
    TrueTexas

    TrueTexas [OP] New Member

    Joined:
    Jun 1, 2021
    Member:
    #21753
    Messages:
    324
    Gender:
    Male
    The Woodlands, TX
    Vehicle:
    2021 Magnetic Grey 4Runner TRD ORP
    Thanks Chris. That is what I was hoping for. I made bumpstop blocks out of HDPE for my Jeep and they are bulletproof. UHMW is even stronger. Will reach out to you.
     
    2016 4Runner SR5 likes this.
  12. Sep 7, 2022 at 5:12 PM
    #12
    2016 4Runner SR5

    2016 4Runner SR5 CONTACT ME FOR CORNFED LIFT SPACERS 631-202-8245

    Joined:
    Jan 29, 2017
    Member:
    #3447
    Messages:
    1,076
    Gender:
    Male
    First Name:
    #Rensing Off-Road
    North Carolina
    Sounds great, thank you.
     
  13. Sep 7, 2022 at 5:27 PM
    #13
    TrueTexas

    TrueTexas [OP] New Member

    Joined:
    Jun 1, 2021
    Member:
    #21753
    Messages:
    324
    Gender:
    Male
    The Woodlands, TX
    Vehicle:
    2021 Magnetic Grey 4Runner TRD ORP
    Now that was the easiest transaction ever! Thanks @2016 4Runner SR5.

    Cancelled my Amazon order for the Moto-Fab part.

    For everyone else out there. UHMW Polyethylene is incredibly strong. It is used in industrial high friction / high strength applications like conveyor belt wheels, bearings etc... It is far superior to other options for this purpose as there is no risk of things like galvanic corrosion from aluminum being in contact with steel and wont rust like painted steel parts if they get scratched.

    If you are in the market for spacers or a shim to correct lean or lift, call Chris.
     
    2016 4Runner SR5 likes this.
  14. Sep 10, 2022 at 8:02 PM
    #14
    Basset_Dad

    Basset_Dad New Member

    Joined:
    Feb 3, 2019
    Member:
    #8677
    Messages:
    22
    Gender:
    Male
    First Name:
    Rick
    Harrison, Ohio
    Vehicle:
    2017 Grey 4Runner TRD OFF Road Premium
     
  15. Sep 10, 2022 at 11:06 PM
    #15
    TrueTexas

    TrueTexas [OP] New Member

    Joined:
    Jun 1, 2021
    Member:
    #21753
    Messages:
    324
    Gender:
    Male
    The Woodlands, TX
    Vehicle:
    2021 Magnetic Grey 4Runner TRD ORP
    @Basset_Dad

    There is no question (for me), go with the cornfed ones from @2016 4Runner SR5. See my comments above.

    Note that I have absolutely no affiliation to Chris, except my contact with him thru this site. I also appreciate and respect his "hustle" as we say in Houston. The spacers he sells are exactly the material I was looking for and the price was ideal. His communication is top notch as well.

    I will post results as soon as I install it. I have no expectations it will 100% fix the lean as it changes based on how much fuel you have in the tank and who is sitting in the vehicle but my goal is to get it as close as I can to level.
     
    2016 4Runner SR5 likes this.
  16. Sep 12, 2022 at 5:33 PM
    #16
    TrueTexas

    TrueTexas [OP] New Member

    Joined:
    Jun 1, 2021
    Member:
    #21753
    Messages:
    324
    Gender:
    Male
    The Woodlands, TX
    Vehicle:
    2021 Magnetic Grey 4Runner TRD ORP
    The Spacer from Cornfed arrived in the mail on Sunday and I installed it today. Drove about 20 miles and filled the tank so I could get some comparable measurements.

    The lean has been greatly reduced. Here are the deltas: NOTE: this is with a 10mm OME spacer in the rear Drivers side and the 1/4" Cornfed Spacer in the front drivers side.

    F 1/8" lean to drivers side
    R 1/4" lean to drivers side.

    Based on my previous full tank measurements, I had an even 1/2" lean both front and rear so this is greatly improved. When empty, I had between 1/4" and 3/8" lean. So it looks like when I'm empty, it will still be pretty close.

    I'm thrilled!!! Worth going back in to correct but if your installing Bilstein 5100s for the first time, do it at the same time you install them.
     
    2016 4Runner SR5 likes this.
  17. Sep 12, 2022 at 5:41 PM
    #17
    TrueTexas

    TrueTexas [OP] New Member

    Joined:
    Jun 1, 2021
    Member:
    #21753
    Messages:
    324
    Gender:
    Male
    The Woodlands, TX
    Vehicle:
    2021 Magnetic Grey 4Runner TRD ORP
    Also, quality of the cornfed spacer was excellent. Came with new nuts (which I used) and instructions (which I did not use)

    Install was simple
    Jack up and remove wheel (use Jack Stands)
    Remove front skid plates and plastic trim
    Remove lower shock nut (leave bolt in)
    Remove 3 upper shock nuts
    Remove 2 lower control arm to spindle bolts
    Loosen lower control arm bushings bolts
    Install spacer and reinstall everything in reverse order. Torque to spec.

    About 1 hour 30 min start to finish.
     
    2016 4Runner SR5 likes this.

Products Discussed in

To Top