1. Welcome to 4Runners.com!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all 4Runner discussion topics
    • Transfer over your build thread from a different forum to this one
    • Communicate privately with other 4Runner owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

Bad vibration coming from front end

Discussion in '3rd Gen 4Runners (1996-2002)' started by stinkyspice, Dec 29, 2020.

  1. Dec 29, 2020 at 12:33 PM
    #1
    stinkyspice

    stinkyspice [OP] New Member

    Joined:
    Nov 20, 2020
    Member:
    #17994
    Messages:
    14
    Gender:
    Male
    First Name:
    Levi
    Vehicle:
    2000 4Runner limited 4x4
    Led swaps tundra brake upgrade
    Hi guys just did the tundra caliper upgrade on my wife’s 2000 4Runner 4x4 limited. Had a problem with the booster being a Tacoma booster. Installed the correct one. And extended the throw of the booster just a bit. Calipers where sticking. One day the truck just started to shake violently in the front end. Driving down the highway, started around 40 with a real light vibration and turns into a baddd vibration jolting the car feeling like you popped a tire almost. It did this on two occasions the brakes smelled baddd so the calipers had to be sticking. Went to drive it to my dads garage to check it out. And the brakes just didn’t work pedal to the floor then it would stop after about a second of the pedal to the floor. Checked it out my mechanic checked the already brand new booster and it was bad. He installed a new one and it seemed to fix the problem just fine for about a week. Braked well no calipers sticking. All of a sudden it started to do the same thing shake violently in the front end around highway speeds. I’m am completely stumped. When I did the tundra upgrade installed new rotors, pads, ss brake lines, calipers, master cylinder and brake booster. Only thing I could think it could be is a bad calipers. They where cheapies from Amazon. But it confuses me because changing the booster seemed to fix the issue until a week went by and it started to do it again. Any ideas or idea on what it might be?
     
  2. Jan 16, 2021 at 1:01 AM
    #2
    Ambush

    Ambush New Member

    Joined:
    Jan 16, 2021
    Member:
    #19144
    Messages:
    21
    Gender:
    Male
    First Name:
    AJ
    Vehicle:
    99 Black Limited (Kitt) 99 Tan limited (Desert Storm) 2001 Silver SR5 (Silver Surfer)
    Hello there!

    Take your brake booster out and master cylinder. Let me know if there is a PAPER gasket in between there. If there is not, that is your issue. It is losing vacuum. The paper gasket is very thin and it needs to be in that shape. YUP I had the same issue.

    LINK Here
     
    This site contains affiliate links for which the site may be compensated.
    #2
    Toy4X4 likes this.
  3. Jan 16, 2021 at 2:46 PM
    #3
    stinkyspice

    stinkyspice [OP] New Member

    Joined:
    Nov 20, 2020
    Member:
    #17994
    Messages:
    14
    Gender:
    Male
    First Name:
    Levi
    Vehicle:
    2000 4Runner limited 4x4
    Led swaps tundra brake upgrade
    so I do have a gasket there it doesn’t look like paper though. I should probably just order the OEM one.

    I believe I figured it out. When I got my pads for the 2005 tundra they sent me 4 pad clips. I dont know why I didn’t check my Tacoma or look it up but I put 2 clips on each caliper. One on the top and one on the bottom of the pads of each caliper. I took off that bottom clip as that’s the OEM orientation. Fixed the problem. I think that it was just enough pressure to keep the pads applied every once in a while causing the jolting in the brakes. Along with my booster knob on the inside being adjusted just a little to far out. I adjusted that with a master cylinder adjustment tool and the pedal feel increased immensely. The pedal was not contacting the rod soon enough because it was to far adjusted out. This fixed the problem! The pedal still feels a little little soft so I’m going to try changing the paper gasket see if that helps. Thanks for the response bro!!!
     
    This site contains affiliate links for which the site may be compensated.
    #3
    Ambush[QUOTED] likes this.
  4. Jan 16, 2021 at 2:52 PM
    #4
    Ambush

    Ambush New Member

    Joined:
    Jan 16, 2021
    Member:
    #19144
    Messages:
    21
    Gender:
    Male
    First Name:
    AJ
    Vehicle:
    99 Black Limited (Kitt) 99 Tan limited (Desert Storm) 2001 Silver SR5 (Silver Surfer)
    AWESOME NEWS!! You are welcome. I love to help!! Im here if ya need anything :)
     
  5. Jan 31, 2021 at 2:39 PM
    #5
    stinkyspice

    stinkyspice [OP] New Member

    Joined:
    Nov 20, 2020
    Member:
    #17994
    Messages:
    14
    Gender:
    Male
    First Name:
    Levi
    Vehicle:
    2000 4Runner limited 4x4
    Led swaps tundra brake upgrade
    So i got a OEM Gasket installed it does feel slightly better. I also changed the return spring the old one felt weak.
    Should there be any play in the brake pedal when pushing it down with your hand until it feels like it engages with the booster rod? I got about a half inch of play i would say until it stops with light pressure. I have a picture of the booster rod coming into the cab. Does this adjustment do anything for the play of the pedal? And if so how do i go about adjusting it?

    8BE085BA-F4D7-48F8-A60F-1DD2806B4070.jpg
     

Products Discussed in

To Top