1. Welcome to 4Runners.com!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all 4Runner discussion topics
    • Transfer over your build thread from a different forum to this one
    • Communicate privately with other 4Runner owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

TRD Pro Skid Plate: Read This First!!

Discussion in '5th Gen Builds (2010-2024)' started by travelinscout, May 1, 2020.

  1. May 1, 2020 at 7:15 PM
    #1
    travelinscout

    travelinscout [OP] New Member

    Joined:
    Feb 18, 2020
    Member:
    #13203
    Messages:
    630
    Gender:
    Male
    Arizona
    Vehicle:
    2020 TRD ORP MGM
    I just finished installing my TRD skidplate, and I would like to share my experience. I was so excited to finally get it installed, that I more or less didn't really pay attention to how difficult it was to get the bolts all the way in. Almost a HUGE mistake. I spent some time today reading about all of the horror stories with broken, stripped, and cross threaded skid plate bolts. All I could think about all day was, will my bolts just snap in half when I try to take them out? I decide to invest, very wisely, in a tap,bottle of cutting oil, and a container of anit-seize. I took my skid plate off, and was very careful in threading the tap in, and cleaning the holes. There was an unbelievable amount of crap in those threads! My truck only has 2800 miles and has hardly seen any dirt, so this was not road dirt, but rather factory installed dirt and crud. Once I had all the threads cleaned, the bolts threaded all the way in with nothing more than my fingers. I put some anti-seize on all 4 bolts, and then properly torqued them. I love my truck and so far this is the only thing I have not been too thrilled about. I think perhaps the installation instructions should add a clean out the threads step. I attached a couple of pics to show the exact tap size I used. Enjoy!Tap and Die 1.jpg Tap and Die 2.jpg
     
  2. May 2, 2020 at 6:47 AM
    #2
    Ironguy

    Ironguy New Member

    Joined:
    Dec 22, 2019
    Member:
    #12421
    Messages:
    6,230
    Gender:
    Male
    First Name:
    Ralph
    Bisbee AZ
    Vehicle:
    2020 Black 4Runner Venture 1967 FJ40 Land Cruiser
    New pine scent hanger, new sun shade
    Great idea and a good tip. I have also heard tales of breakage after dealer oil changes.
     
    DrewMan and travelinscout[OP] like this.
  3. May 2, 2020 at 8:10 AM
    #3
    1bad2k

    1bad2k New Member

    Joined:
    Feb 14, 2018
    Member:
    #5490
    Messages:
    62
    Gender:
    Male
    First Name:
    Sam
    Vehicle:
    2000 SR5 4x4 4R
    I did the same. The thread cutting oil isn't really necessary to just change the thread pitch a little bit. The new bolts go in super smooth now!
     
    DrewMan and travelinscout[OP] like this.
  4. May 2, 2020 at 10:38 AM
    #4
    Oldtoyotaguy

    Oldtoyotaguy Paid cash for it

    Joined:
    Sep 21, 2018
    Member:
    #7224
    Messages:
    1,599
    Gender:
    Male
    Vehicle:
    2018 Toyota 4 Runner Offroad
    Great post, smart move, travelinscout! There are other instances as well when your approach would be very helpful. Toyota uses a lot of fine threaded bolts, and these can easily cross thread in a rusted nut. Once it breaks and is broken off in there, it is a big job to get it back out again. Some so called professional mechanics being paid on a flat rate just hope it isn’t noticed and stick it back together without troubling to fix the broken or crossed threaded bolt.
     
  5. May 3, 2020 at 3:08 AM
    #5
    rkwfxd

    rkwfxd New Member

    Joined:
    Mar 14, 2018
    Member:
    #5662
    Messages:
    642
    Gender:
    Male
    First Name:
    Rich
    Whittier - So Cal
    I had heard about these issues and was concerned when I recently installed my RSG skid plate. Man what a surprise! All of my bolts came out easily and the new ones threaded in perfectly. Guess I got lucky again.
     
  6. May 3, 2020 at 5:06 AM
    #6
    Jynarik

    Jynarik I like boobies

    Joined:
    Jul 10, 2019
    Member:
    #10510
    Messages:
    2,183
    Gender:
    Male
    Austin Texas
    Vehicle:
    2019 trd pro voodoo
    1st oil change no problem. This last one, for whatever reason, took me forever to get a single bolt started. I feel like I cross threaded one of them. Any tips on fixing that issue next oil change?
     
  7. May 3, 2020 at 5:25 AM
    #7
    Charlievee

    Charlievee New Member

    Joined:
    Dec 20, 2018
    Member:
    #8149
    Messages:
    1,287
    New bolt and retap it.
     
  8. May 3, 2020 at 5:36 AM
    #8
    Charlievee

    Charlievee New Member

    Joined:
    Dec 20, 2018
    Member:
    #8149
    Messages:
    1,287
    Credit where credit is due. Thank you Cymon (2017)Saker (2014). I would also suggest grade 8 bolts for all the skid plates.
     
    DRobs, travelinscout[OP] and Jynarik like this.
  9. May 3, 2020 at 5:38 AM
    #9
    Jynarik

    Jynarik I like boobies

    Joined:
    Jul 10, 2019
    Member:
    #10510
    Messages:
    2,183
    Gender:
    Male
    Austin Texas
    Vehicle:
    2019 trd pro voodoo
    thanks. Do we know what size bolts they are before I dig through the parts diagram?
     
  10. May 3, 2020 at 5:47 AM
    #10
    Charlievee

    Charlievee New Member

    Joined:
    Dec 20, 2018
    Member:
    #8149
    Messages:
    1,287
    10mm 1.25 TRD plate
    8mm 1.25 all the rest.

    ... For a 5th Gen.
     
    travelinscout[OP] likes this.
  11. May 3, 2020 at 6:30 AM
    #11
    Agent_Outside

    Agent_Outside A Guy A Girl and A Trail

    Joined:
    Dec 18, 2018
    Member:
    #8098
    Messages:
    1,933
    Colorado
    Vehicle:
    Built 2011 T4R Limited
    Just an FYI - something worth mentioning is a tap is not the “correct” tool for this job. A tap is for cutting new threads and it’s very easy to damage existing threads using one because it’s not meant to follow existing threads, it’s meant to start cutting new threads at the first sign of resistance. A thread chaser is specifically for cleaning up and fixing existing threaded holes.
     
  12. Jun 5, 2020 at 11:03 AM
    #12
    gjbush

    gjbush New Member

    Joined:
    May 22, 2020
    Member:
    #14478
    Messages:
    11
    Gender:
    Male
    First Name:
    Gregory
    Vehicle:
    Toyota 4Runner TRD Premium
    Where can you purchase the 10mm thread chaser for this application?
    Is this tool the best and is it long enough?
    Amazon Performance Tool W83163 Spark Plug Chaser, 10mm/14mm
     
    Last edited: Jun 5, 2020
  13. Jun 5, 2020 at 11:20 AM
    #13
    Dillusion

    Dillusion New Member

    Joined:
    Dec 10, 2018
    Member:
    #7998
    Messages:
    2,687
    Gender:
    Male
    First Name:
    KYle
    Vehicle:
    2018 TRD OR
    No pics of dirty bolts?
     
  14. Aug 22, 2020 at 2:44 PM
    #14
    erfer1

    erfer1 New Member

    Joined:
    May 17, 2020
    Member:
    #14364
    Messages:
    206
    Gender:
    Male
    First Name:
    Eric
    SW NM
    Vehicle:
    2019 Limited
    I finally installed mine today. Threads were in rough shape. (Buried the runner on day 2 of ownership) On the plus side, the extra fascia on the Limited does away with the need to trim for gap coverage. Spent more time cleaning up than installing.
     
    travelinscout[OP] likes this.
  15. Aug 23, 2020 at 6:10 AM
    #15
    V4runner

    V4runner New Member

    Joined:
    Jul 29, 2020
    Member:
    #15818
    Messages:
    81
    Gender:
    Male
    First Name:
    Vikash
    Vehicle:
    2019 Sr5 Premium
    Daystar Leveling Kit
    Does this hardware kit solve the problem?

    Hardware Kit. Front Skid Plate.

    Part Number: PT93800140AA
    Supersession(s): PT938-00140-AA
    [​IMG]
     
    Last edited: Aug 23, 2020
    This site contains affiliate links for which the site may be compensated.
    #15
    brownersd likes this.
  16. Aug 23, 2020 at 6:25 AM
    #16
    erfer1

    erfer1 New Member

    Joined:
    May 17, 2020
    Member:
    #14364
    Messages:
    206
    Gender:
    Male
    First Name:
    Eric
    SW NM
    Vehicle:
    2019 Limited
    My hardware fit fine. The threads were filled with crap. I used the tap, I am familiar with using taps and die and chaser. I sprayed penetrating fluid into each thread, lubed the tap, and carefully threaded and un threaded. Worked a treat. Patience.
     
    Last edited: Aug 23, 2020
    V4runner[QUOTED] likes this.
  17. Aug 23, 2020 at 6:56 AM
    #17
    V4runner

    V4runner New Member

    Joined:
    Jul 29, 2020
    Member:
    #15818
    Messages:
    81
    Gender:
    Male
    First Name:
    Vikash
    Vehicle:
    2019 Sr5 Premium
    Daystar Leveling Kit

    Thank You!
     
  18. Aug 29, 2020 at 9:15 AM
    #18
    joeman

    joeman New Member

    Joined:
    Jul 26, 2020
    Member:
    #15757
    Messages:
    34
    Gender:
    Male
    Scottsdale, AZ
    Vehicle:
    2020 4Runner Venture
    This thread was very helpful -- no pun intended :) Thanks to everyone who contributed above, helped me out big time!

    Had the very same problem with a 2020 with only 300 miles on it. Front bolts went in no problem. But the rear two bolts only went in half way, then I hit a wall. The bolts that come with the TRD skid plate are much longer than the bolts you have to remove from the factory when you install the skid plate.

    Here's what worked for me:

    1. Bought this tap (about $7)
    2. Bought this T Handle (about $14)
    3. Instead of thread cutting oil, I used WD-40. Worked for me an I already had it.
    4. Sprayed the tap
    5. Carefully screw in straight...as mentioned above, slow and careful.
    6. You will feel some resistance, keep going. Screw in one turn, then back out 1/2 turn to release the debris. Repeat. Repeat.
    7. I actually backed all the way out a few times to clean the tap and re-spray with WD-40.
    8. As mentioned above, bolts go in by hand pretty easily now...just take your time!

    Pics below of what I bought in case the links go bad..

    image_8144c52d-6bfa-4ffb-b8c1-339f3d1c421c_large.jpg s-l400.jpg
     
    Last edited: Aug 29, 2020
    erfer1 and V4runner like this.
  19. Oct 19, 2020 at 4:17 PM
    #19
    vjoseph

    vjoseph New Member

    Joined:
    Oct 19, 2020
    Member:
    #17423
    Messages:
    1
    Gender:
    Male
    joeman, Thank you for your post, I just bought a Venture 2020 myself and was looking for someone who installed it. one question though, any problem with going with suppressors like user V4runner showed which avoid taping?

    Thanks
     
  20. Oct 19, 2020 at 5:02 PM
    #20
    joeman

    joeman New Member

    Joined:
    Jul 26, 2020
    Member:
    #15757
    Messages:
    34
    Gender:
    Male
    Scottsdale, AZ
    Vehicle:
    2020 4Runner Venture
    Not sure about that. Tapping was easy though...just take your time, use WD-40 or oil as described earlier. Bolts come out and go in easily after I did what I described above.
     
  21. Mar 11, 2021 at 1:16 PM
    #21
    Crazed4runners

    Crazed4runners New Member

    Joined:
    Jan 14, 2021
    Member:
    #19113
    Messages:
    9
    Mountain West
    Vehicle:
    2021 LR TRD Pro & Red TRD Off Prem
    Making them as we go. The red TRD Off has an Icon stage 7, Relations Wheels and Toyo Tires.
    I just did my TRD Off Premium (no KDSS) last weekend. No thread issues. I used anti seize. It was, however, a pain in the ass to line up the holes and get them started as I am only one may with two arms and two legs. Thank goodness for the legs.
     
    Gracio and joeman like this.
  22. Nov 13, 2021 at 2:18 AM
    #22
    Pierrep4

    Pierrep4 New Member

    Joined:
    Nov 13, 2021
    Member:
    #24231
    Messages:
    2
    Gender:
    Male
    First Name:
    Pierre
    Vehicle:
    2021 4Runner SR5 premium
    I just installed the TRD skid plate on my 21 SR5 P. You can get all that gunk out with a 9mm brass borebrush with cleaning solvent. It worked perfect for me and did not have to rethread the hole. After a thorough cleaning they went in easily.
     
  23. Nov 13, 2021 at 5:29 AM
    #23
    Charlievee

    Charlievee New Member

    Joined:
    Dec 20, 2018
    Member:
    #8149
    Messages:
    1,287
    Saker's life changing skid plate mod. Parts list to install threaded studs and acorn nuts to hold up the skid. Make mounting and removing the skid, almost enjoyable. 42AB5CC9-5CFB-4466-88A7-F3A61A417ADF.jpg
     

Products Discussed in

To Top