1. Welcome to 4Runners.com!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all 4Runner discussion topics
    • Transfer over your build thread from a different forum to this one
    • Communicate privately with other 4Runner owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

Camshaft Seal replacement

Discussion in '2nd Gen 4Runners (1990-1995)' started by Dakotaharrold, Sep 21, 2020.

  1. Sep 21, 2020 at 5:24 PM
    #1
    Dakotaharrold

    Dakotaharrold [OP] Yota the Toy

    Joined:
    Sep 21, 2020
    Member:
    #16873
    Messages:
    4
    First Name:
    Dakota
    Portland OR
    Vehicle:
    1993 V6 3.0L 4Runner
    Lift, wheels, tires, exhaust
    Any special tools/equipment needed for a camshaft seal replacement on the 1993 3.0L?!

    Any insight on what to do/not do while attempting?

    I plan on doing water pump, timing belt and exterior belts too, any parts cost knowledge of things other parts needed?

    Thanks in advance!
     
  2. Sep 21, 2020 at 6:18 PM
    #2
    watermelonman122

    watermelonman122 New Member

    Joined:
    Jul 4, 2020
    Member:
    #15297
    Messages:
    84
    Utah
    Vehicle:
    1994 4Runner SR5 3.4 V6 4wd 5spd
    Other than the typical hammer and something to hammer with you need to install a seal, the tricky part is removing the seal. The camshaft seals, like the oil pump seal (which would be worth doing while you have the timing belt off), are tough because the shaft still goes through the seal so there's no room to get a screwdriver in there. I would highly recommend getting a puller tool (such as https://www.amazon.com/Lisle-58430-Shaft-Type-Puller/dp/B000FPYW4K). It's not a perfect solution and will probably need to be bent back in shape while using it, but it's much better than trying to use a screwdriver and gouging the camshaft. You'll also want to get or borrow a cam pulley holder tool (such as https://www.amazon.com/Performance-Tool-W89208-Pulley-Maximas/dp/B002KSEJ6Q) for holding the cam pulley in place while you take off the bolt holding it on. I made do with a serpentine belt tool and a hose clamp, but was very sketchy and left unsightly marks on the purty cam pulleys. Ummm, I would go with OEM seals from Toyota. They're affordable for OEM and not worth going cheap on. While you have all of that off, might consider getting new idler pulleys too. Both of mine were making slight grinding noises when I replaced them and they're pretty affordable as well.

    If you don't have some already, you'll need RTV for the water pump (and top idler pulley if you decide to replace that). They make a specialized RTV for water pump and coolant applications.

    The whole reason I had to take mine apart in the first place was because the 'Radiator Fan Clutch Bearing' seized up and broke my alternator belt. Once you have it off, I would spin it and give it a listen and see if it's making noise, because if that things fails, you're dead in the water and it's a pain getting out because it's behind the other two accessory belts.

    The AISIN Timing Belt, Water Pump, and Component kit on RockAuto goes for about $187. With the seals, accessory belts, and various products that come out of a tube, I'd say this can all be done for less than $250. It goes without saying, but take your time and do it right. Don't want to have to take it apart again once you're done. Best of luck and let us know how it goes.
     
    atgparker likes this.
  3. Sep 21, 2020 at 8:53 PM
    #3
    Dakotaharrold

    Dakotaharrold [OP] Yota the Toy

    Joined:
    Sep 21, 2020
    Member:
    #16873
    Messages:
    4
    First Name:
    Dakota
    Portland OR
    Vehicle:
    1993 V6 3.0L 4Runner
    Lift, wheels, tires, exhaust
    Great response and thanks for the insight, glad to know I can get such thorough answers by members here!

    So the puller tool would need to be modified to actually function properly for this job? Would it also work for oil pump seal?! I've been quoted insane labor costs from shops and understand it can be a bitch but if no engine pull or specialized equipment is required, I think it would be worth it to give it a go.
     
  4. Sep 21, 2020 at 10:28 PM
    #4
    watermelonman122

    watermelonman122 New Member

    Joined:
    Jul 4, 2020
    Member:
    #15297
    Messages:
    84
    Utah
    Vehicle:
    1994 4Runner SR5 3.4 V6 4wd 5spd
    The puller tool doesn't need to be modified to start, but it gets bent easily and will need to be bent back between pulls. Yes it works on both the camshafts and the oil pump seal.

    No engine pull required. A 10, 12, and 14mm will get you most of the way. If you make sure to follow the FSM, it's not a hard job. Takes some time, but not very difficult.
     
  5. Sep 22, 2020 at 10:39 AM
    #5
    Fishguy

    Fishguy New Member

    Joined:
    Aug 31, 2020
    Member:
    #16446
    Messages:
    37
    Gender:
    Male
    Vehicle:
    95 4Runner (stock)
    Replaced EGR vacuum modulator!
  6. Sep 22, 2020 at 1:49 PM
    #6
    Dakotaharrold

    Dakotaharrold [OP] Yota the Toy

    Joined:
    Sep 21, 2020
    Member:
    #16873
    Messages:
    4
    First Name:
    Dakota
    Portland OR
    Vehicle:
    1993 V6 3.0L 4Runner
    Lift, wheels, tires, exhaust
    @Fishguy epic hack, does it look like the engine is pulled to be able to access that way?

    Thanks for the insight ✊
     
  7. Sep 22, 2020 at 2:23 PM
    #7
    Fishguy

    Fishguy New Member

    Joined:
    Aug 31, 2020
    Member:
    #16446
    Messages:
    37
    Gender:
    Male
    Vehicle:
    95 4Runner (stock)
    Replaced EGR vacuum modulator!
    I don't think the engine/trans/whatever needs to be pulled as long as you can get a screw in there without harming the shaft and ya got room to pull it out.

    I haven't tried it yet. I am afraid to wish for a chance.;)
     
  8. Sep 22, 2020 at 2:47 PM
    #8
    watermelonman122

    watermelonman122 New Member

    Joined:
    Jul 4, 2020
    Member:
    #15297
    Messages:
    84
    Utah
    Vehicle:
    1994 4Runner SR5 3.4 V6 4wd 5spd
    That's genius. Wish I'd known about that trick. Given that I used a hammer and punch to put the seal in, I'm sure there's enough room on all three of those seals.

    0712201328.jpg
     
  9. Sep 25, 2020 at 11:15 AM
    #9
    atgparker

    atgparker Cal Poly, ETME 1988

    Joined:
    Jun 20, 2018
    Member:
    #6296
    Messages:
    328
    Gender:
    Male
    First Name:
    Andrew
    Mission Viejo, CA
    Vehicle:
    1991 White 4Runner 3.0 L
    Rebuilt Engine MLS and ARP on the heads, DT Header, 2-1/2" CARB compliant Flow-Master CAT with 2.0" Bosal CAT back Dayco 1-1/4" Spacers, SkyJacker M-Series Monotube Shocks, Ball Joint Spacers. 95-9006 K&N Air Cleaner, G-Plus Alum Radiator, ZIrgo 16" Fan, Derale Temp switch/relay
    Now pull the dowel pins that key the pulleys to the camshafts. Set pulleys on the cams and loosely install the bolts so the pulleys can spin on the cams. Set the timing belt and marks in place at TDC for #1 and set the tensioner. Rotate the crank shaft 2 revolutions and see that the marks realign when you reach TDC for #1. Yank cam pulley bolts and rotate crank to put dowels back in and torque cam pulley bolts to specification.

    If you do it this way you don't have to fight with the cams and valve springs trying to move the pulleys while you get the belt set up correctly.
     
    Last edited: Sep 25, 2020
  10. Sep 29, 2020 at 9:58 PM
    #10
    Dakotaharrold

    Dakotaharrold [OP] Yota the Toy

    Joined:
    Sep 21, 2020
    Member:
    #16873
    Messages:
    4
    First Name:
    Dakota
    Portland OR
    Vehicle:
    1993 V6 3.0L 4Runner
    Lift, wheels, tires, exhaust
    @atgparker thanks for the added tip! Much appreciated.
     

Products Discussed in

To Top