What have you done to your 5th Gen 4Runner today?

Yes some differences in the motors despite sharing the same engine code.

The 4 runners version of the 1GR-FE engine has new pistions that are hollowed near the crown, new cylinder heads using hydrolic lash adjusters with VVTi on both the exhaust and intake (dual vvt-i) cams. Other minor changes are the ACIS Valve in the plenum was deleted and a larger throttle body is used. The air filter box was changed and is now over at the fender like the Tundra and the MAF sensor has been changed to the new membrane type. The oiling system was changed with the oil filter down low under the crank pulley and it uses a cartridge type oil filter now. The crankshaft has been lightened with fewer counter weights used. Other than that, same motor.

 

Engine, not motor. Also makes about 35 more horsepower than it used to so those changes must have been worth it.

 

Yeah the main difference is that dual VVT-I. I know when I had my Tacomas it would have been real nice to have this 4runner motor in it.

 

i like these thanks for the Info i was going to do the mirror swap

 

No problem and it actually works good. I only drive my Runner a few times a week but I can see the BSM does work. You can't go wrong for a less then $10 upgrade!

 

Mine comes in this week, can't wait to go blind spotting.

 

let us know how you like them i have a set in my cart but haven't bought yet. thanks

 

I have read this entire thread today...my Christmas list is huge now! Getting my girl a new lift and some shoes today! Can't wait to pick her up!

 

Got some rubbing on the front fender and I hated the running boards so they're gone... Now to figure out what rockers to put on it. I feel bad for anyone riding my ass... I'm tossing rocks bad!

Here we go is right! And the awning and shovel will be put back on it tomorrow. Ohmagheeeeerd! ❤️

 

Why upgrade to these? Just curious.

 

Those Black housing LED fog lights is plug/play and looks pretty cool
I just replaced my stock fog bulb's with LED's and super bright to match my head light LED's.....

 

Which headlight LED did you install and do you like them?

 

Added TRD knob

 

I wanted OEM black housing LED and a not fan of the Morimoto fitment. Morimoto's fit my previous Tacoma better than the 4Runner.
I do think the Lexus LED(same as 18 Tundra LED) has a better output than these.

 

Sweet lookin rig..! One of the lucky ones to have a Gobi... Welcome from Colorado

 

So you are upgrading to get a brighter light and LED ?
I got the tinker bug again and I’m a big fan of he easy plug and go method. Was it easy?

 

Put in Headlight Revolutions LEDs. Used them in my Tacoma with good luck, installed these today.

https://headlightrevolution.com/2014-2018-toyota-4runner-low-e beam-supernova-perfectfit-led-headlights/

I’ll take some pics nextime I am out at night. They look good on the garage wall, for sure brighter than the stock halogens and have a nice cutoff.

 

LED runs brighter than the 19W H16 halogen. Install was easy, maybe 2 min per side.

 

No flickering issues or extra wiring involved? I ran led in my 2015 Tacoma and it was a little more tonot for install. Had to use wire taps and run a ground all the while mounting transistors behind the grill. Wasn’t bad but was more than just a typica bulb swap.
The leds also had fans attached to them for cooling

 

How was the install ? Were there any mods needed for the install? Did you need to adjust them once installed ?

 

I was referring to my fog lights only.
For headlights I’m content with HIDs from Xenon Depot.

 

I got some new wheels and tires put on yesterday. Liking it much better than stock.

 

I looked at the headlightrevolution.com LED for 2014-2018 4Runner. I did some research on Amazon and narrowed it down to this direct plug and play LED Light. They are for sure brighter and white than the stock halogen lamps that came on my 4R. I decided to try these @ $28.99 before spending $100 plus. These $28.99 LED's are doing pretty darn good, but I have not replaced halogen to LED before this time. https://www.amazon.com/gp/product/B07GWF2JXZ/ref=oh_aui_detailpage_o05_s00?ie=UTF8&psc=1

 

Install was easy, less than 10 minutes, no modifications needed, dust cover still fits, I did not adjust them.

 

TRD wheels looks great with ur Red.....

 

Oh ok right on. I shouldn’t read to early in the morning before having my coffee lol

 

Thanks for the feedback I’ll be installing a set. Now to decide what to do for the rest of them.

 

Installed my Greenlane OffRoad sliders, drivers side was a pain, took 1 1/2 hours, passengers side was a breeze, less than 1/2 hour. Torqued everything to 35 ft. lbs. Winch mount due in this Wednesday, that will be a fun project.

 

Added front/rear door speakers......Waiting for Amp kit to come in to add the Alpine 4 Channel into the Audi Control LC6 then wiring into speaker outputs of the stock deck. Sound difference with just the speakers alone is major. I can just imagine getting Amplified!

Pics are stock vs JBL's.
6x9" are front doors
6.5" are rear doors

Already have a 10" JL Sub is the rear corner pocket.....