What have you done to your 5th Gen 4Runner today?

Mine all sat flush, but I also put a little rtv sealant for added protection.

 

https://www.tufskinz.com/collection...o-grill-toyota-4runner?variant=39603185811552

 

Installed a ladder yesterday.

I'm going to be going on a 3 week road trip in remote territory and wanted some extra fuel. I vividly remember four times in my life where a planned fuel stop didn't work out (once due to area fuel shortage, two due to extended power outages, one because the only fuel stop in between two communities was closed for the season), and prefer to not relive that.

So all that being said, I basically bought a ladder to hold 100km's of fuel...but my wife will be able to use it to access the roof.

Are there better options...very much yes. I would prefer to have a swing away tire carrier and then get NATO can holders on that (or even one of those spare tire fuel cans) but cost was a factor, and at least the ladder will be used for actual laddery things. There is no room on the roof, and even if there was room up there I'm suspicious of laying down Rotopacks on the roof.

The ladder is a C4 Summit, and its holding the 3 gallon Rotopack...has anyone else used that same combo? Is that mount sturdy enough for the weight of the fuel if not being abused on extremely rough roads?

 

My C4 is due for delivery today. Any cautions on install or did it go as planned? I bought and then sold a Gobi that I thought was insufficient, hoping the C4 is a notch or two up.

 

Replaced the wiper blade inserts. After 92K miles, the passenger side was still in ok shape. The driver's side was starting to separate.

Part numbers:
85214-06140
85214-0E140 (replaces 06130)

 

I had two hangups:
1. when I unboxed it at my shop I found the three backing plate bolts were missing (the ones that clip in), so definitely check that you have all parts right away
2. There are no actual written instructions, so you have to watch the damn YouTube video.

But overall, the install was easy, and the video I was just bemoaning is actually quite thorough, and worth a pre-watch. I did it solo, and it was not difficult

Edit: I have the version that bolts to the bottom of the rear gate. Not sure if that's the new one or the old one, but I think I heard of some that kind of clamp on

 

Yeah I miss the old days when you got actual instructions with your purchase but I guess it saves on paper. How do you feel about quality, meets your expectations?

 

I keep hitting the like button instead of the quote button!

As far as quality, I'm actually somewhat surprised at how good it is. I originally thought it seemed a little hokey with the 2-way stick tape, but its very stable...more stable than my brain thinks it should be. And the material itself is very robust.

 

Yeah I should be all that and more considering the sticker price, half again as much as the Gobi. I do like quality so looking forward to that. Have a great trip.

 

Eibach pro truck stage 1, SPC uca’s, BFG K02’s 285/70/17, 15% tint all around

 

I don't have answers to your questions, but I can see you got an Rotopax and not a Fuelpax which is considered a higher quality product than Fuelpax. Will it fade and/or bulge over time? Maybe. But Fuelpax wouldn't last as long. At least, that's what I've heard.

 

Looks great. I may just get one.

 

Maybe not what I did, but what I saw. Saw a new army green Tundra. Sharp looking truck. But really liked the tag on it.

 

how old is that tire?

 

Nearing 5yrs, my spare is nearing 8

 

Wife went out shopping so I had a free evening to wash my truck and give it a coat of Chemical Guys sealant/wax. I applied using my new DA polisher and wow, I've wasted so much time in my life in the past applying wax by hand. Took maybe 30-45 minutes to coat the entire vehicle and wipe it off.

 

2023 T4R Limited full time 4wd:

Installed TW IR NANO CERAMIC at Tint World to back, sides, moon roof and windshield. Used FL legal tint levels all around and clear on windshield. This is their highest rated product/ Plutonium Grade Scratch Resistant, ect. Cost me $1K incl. tax. Lifetime warranty. Changed the entire look of the vehicle. Very nice. Only 4K miles, can't wait to run out the orig tires to change to 275/55/20.

 

Had to upgrade to a heavy duty struts just for the ladder after installing my C4 ladder. Learned the hard way that I needed it, basically the stock ones was not strong enough to hold up the hatch and it landed on my head. There are struts for gas can and ladder.

 

which struts did you go with?

 

With the ladder alone I needed to just barely assist opening. With the empty can on it took some effort to lift but stayed up on its own. Strut upgrade is high on my list though, just have to revisit the dozens of threads talking about the make and model people are using; I'm hoping I saved the info the first time I was digging through.

 

Looks good, I'm considering the Eibach stage 1. How much lift from stock? Did you do some trimming of the front wheel well for the 285s?

 

This is the struts I went with. They offer 2 types, one for ladder only and the other one for ladder and gas can. I don't know the part number for the one for the ladder/gas can. You can email them. They get back to you quickly.

 

It can support over 200lbs.

 

I have the C4 ladder and 2 gal rotopax mounted on it. I have had no issues with the set up and I do frequent rough trails. I vent the rotopax each day when on a trip.

 

Had to replace brakes so upgraded to PowerStop Z36 kit with the zinc plated rotors and carbon fiber pads. Since she’s got so much extra weight I wanted some extra stopping power.

 

Thanks for that. I was only a little worried after I installed everything and then read on the C4 Fab website "up to 2 gallon size Rotopax can be attached"

 

I did mount my rotopax closer to the top of the ladder to keep the weight closer to the pivot point. Even with doing that I had to change to stronger struts. Stock ones could not hold the weight. The colder the weather the quicker the hatch would hit me on the head. No issues since changing struts.

 

Check out my build page, the details are there.

 

Picked up blk aluminum alloy grille mesh from post office, finally

4x8mm

 

It gave me 2” in the front on the bottom clip,(bought them pre-assembled) and 1” in the back, i used a line laser to measure, the spc’s are set at the +2.0° castor and they rubbed the Mudflaps at full lock , i ended up just taking them off. I love the way it rides and looks now, they should come stock like this