1. Welcome to 4Runners.com!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all 4Runner discussion topics
    • Transfer over your build thread from a different forum to this one
    • Communicate privately with other 4Runner owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

New Owner - Need Advice

Discussion in '5th Gen 4Runners (2010-2024)' started by Dakotawright, Jan 11, 2020.

  1. Jan 11, 2020 at 3:49 AM
    #1
    Dakotawright

    Dakotawright [OP] New Member

    Joined:
    Jan 11, 2020
    Member:
    #12661
    Messages:
    15
    Gender:
    Male
    First Name:
    Dakota
    Vehicle:
    5th Gen. SR5
    Hello. I just purchased a 2016 4Runner SR5 RWD. Before you ask, 4WD is not needed where I live.

    My 4Runner will be my daily driver (I’m a full time real estate investor and Realtor). I need some advice on lift kits.

    Currently I’m sitting stock everything with highway tires. Attached are photos. I would like to get a lift kit and a set of tires and rims with a negative offset for a more aggressive look. For lifts, should I just do a leveling kit for the front? A small lift in back and front? Or should I jump in and do a 2in rear and 3in front?
    My concern comes from being a former Grand Cherokee (05) owner. I had the truck lifted only 2 inches and my tires wore horribly (inside or outside only). I was told it was because of the lift and because I didn’t replace UCA to accommodate lift. Is that the case with 5th gen 4Runners? I don’t want to make a mistake again. Someone guide me in the right direction :)

    I have also attached a photo of a 4Runner I found online that I would like to achieve with my own.

    5586AA5B-D6F4-434B-9BED-53B522F3AD26.jpg
    D3825C20-1D21-41D1-B959-D9583EDBCA36.jpg
     
    Last edited: Jan 11, 2020
    4runGirl88, Thatbassguy and WallyT4R like this.
  2. Jan 11, 2020 at 5:52 AM
    #2
    Matze

    Matze Fremdsprachler

    Joined:
    Nov 5, 2019
    Member:
    #11881
    Messages:
    486
    Gender:
    Male
    First Name:
    Matt
    Lady Lake, FL
    Vehicle:
    2020 4Runner ORP
    Welcome aboard
    I can’t give you advice what to do, it’s a thing of preference and needs, fact is that UCAs are highly recommended above a certain lift hight.
    The best is you slow down, read some threads and dive into it. As more you know about it, the options, the pro and cons and then decide. The 4Runner can be a long lasting friend, so don’t put yourself in a hurry!
     
  3. Jan 11, 2020 at 5:56 AM
    #3
    Dakotawright

    Dakotawright [OP] New Member

    Joined:
    Jan 11, 2020
    Member:
    #12661
    Messages:
    15
    Gender:
    Male
    First Name:
    Dakota
    Vehicle:
    5th Gen. SR5
    Thank you @Matze ! That is why I purchased it.. ready for my forever vehicle. What is the certain height it starts being recommended for UCA? I've read several things in forums... 2 ,2.5, and 3.
     
  4. Jan 11, 2020 at 6:30 AM
    #4
    SCMountaineer

    SCMountaineer New Member

    Joined:
    Dec 18, 2018
    Member:
    #8116
    Messages:
    433
    Gender:
    Male
    Upstate South Carolina
    Vehicle:
    On my third 5th gen — 2021 SR5 premium 4wd
    Gunmetal TRD wheels, Yakima rack, Canvasback covers
    I’ve no advice on what you asked about, but welcome!
     
    Dakotawright[OP] likes this.
  5. Jan 11, 2020 at 6:36 AM
    #5
    SlvrSlug

    SlvrSlug Slightly bent.

    Joined:
    Jun 3, 2018
    Member:
    #6172
    Messages:
    7,542
    Gender:
    Male
    First Name:
    John
    Ramona Ca.
    Vehicle:
    2017 4-Runner SR-5 P. Kings, Built Right uca’s, Durabumps, RSG sliders
    Welcome to the forum.
     
    Dakotawright[OP] likes this.
  6. Jan 11, 2020 at 7:13 AM
    #6
    glwood54

    glwood54 Stop making me buy stuff!

    Joined:
    Aug 19, 2019
    Member:
    #10964
    Messages:
    5,536
    Gender:
    Male
    First Name:
    Gary
    Albuquerque, NM
    Vehicle:
    2019 OR, KDSS, RSG sliders, Eibach shocks, 265/70 Falken Wildpeaks
    @Dakotawright, what size tires do want to change to? That has a bearing on the lift size you'll need.

    I can't speak from experience, but I would think 2" in the front & 3" in the rear wouldn't work very well, the rear is already higher. Did you mean the other way around?
     
    Dakotawright[OP] and KSJ08 like this.
  7. Jan 11, 2020 at 7:21 AM
    #7
    Charlievee

    Charlievee New Member

    Joined:
    Dec 20, 2018
    Member:
    #8149
    Messages:
    1,287
    Lots of people are pleased with the Eibach kit ( myself included). Its about a 2.5 lift overall no need for UCA's and is one of the lower priced complete kits out there ( if you can get your hands on one). There's plenty of options depending on budget, bilstien shocks are another option. Just google 4runner lift and hundreds of links will pop up.
     
  8. Jan 11, 2020 at 7:31 AM
    #8
    glwood54

    glwood54 Stop making me buy stuff!

    Joined:
    Aug 19, 2019
    Member:
    #10964
    Messages:
    5,536
    Gender:
    Male
    First Name:
    Gary
    Albuquerque, NM
    Vehicle:
    2019 OR, KDSS, RSG sliders, Eibach shocks, 265/70 Falken Wildpeaks
    Also, coming from Tacomaworld, I know that Tacoma 2WD trucks had other options for lifting the front vs. 4WD, i.e. a different spindle instead of taller springs. Anyone know if the 4R is the same?
     
  9. Jan 11, 2020 at 8:21 AM
    #9
    Matze

    Matze Fremdsprachler

    Joined:
    Nov 5, 2019
    Member:
    #11881
    Messages:
    486
    Gender:
    Male
    First Name:
    Matt
    Lady Lake, FL
    Vehicle:
    2020 4Runner ORP
    Since some UCA give you one xtra inch of travel it’s not as easy to say you don’t need UCAs with a 2.5” lift... as I said it is a question of needs and preferences!
    A simple, cheap lift maybe looks cool but it doesn’t help off road, nether it won’t make my ... bigger so there would be no gain in my case!
    In case you wanna go step by step I would say get the adjustable bilstein coil overs for the front axle and the shocks for the rear, next step get the ucas adjust the coil overs to max. and put +1” springs to the rear.
    But again, take your time, read up some threads, learn what your 4Runner is already able to do without a lift, gain your knowledge and your decision will be good. I’m in the same process and let me tell you: better boring stock as a half ass mod on it.
     
    Thatbassguy and Dakotawright[OP] like this.
  10. Jan 11, 2020 at 8:46 AM
    #10
    edgesalon

    edgesalon New Member

    Joined:
    Sep 16, 2018
    Member:
    #7148
    Messages:
    614
    Gender:
    Male
    First Name:
    Te
    Vehicle:
    18 FunRunner :-)
    welcome and Congrats on your new ride. i take it you wanted to look like the last picture
    depending on your needs you have tones of options spacers or lift kits
    make sure do your research so you don't have to do it twice there is a lot of info on this forum and may i suggest going to a 4X4 store and see some rigs so you get a better idea of what is possible good luck
     
  11. Jan 11, 2020 at 8:50 AM
    #11
    Dakotawright

    Dakotawright [OP] New Member

    Joined:
    Jan 11, 2020
    Member:
    #12661
    Messages:
    15
    Gender:
    Male
    First Name:
    Dakota
    Vehicle:
    5th Gen. SR5
    I did, lol.. whoops. :D
     
    Thatbassguy and KSJ08 like this.
  12. Jan 11, 2020 at 8:52 AM
    #12
    Dakotawright

    Dakotawright [OP] New Member

    Joined:
    Jan 11, 2020
    Member:
    #12661
    Messages:
    15
    Gender:
    Male
    First Name:
    Dakota
    Vehicle:
    5th Gen. SR5
    Yes, just for looks. I love the 2014+ models are they already look aggressive.. but I don't think I can say I've ever owned an suv without lifting it haha.
     
    4runGirl88, Thatbassguy and KSJ08 like this.
  13. Jan 11, 2020 at 8:53 AM
    #13
    Dakotawright

    Dakotawright [OP] New Member

    Joined:
    Jan 11, 2020
    Member:
    #12661
    Messages:
    15
    Gender:
    Male
    First Name:
    Dakota
    Vehicle:
    5th Gen. SR5
    Thanks! Doing it twice is something I definitely want to avoid.
     
    KSJ08 likes this.
  14. Jan 11, 2020 at 9:02 AM
    #14
    Charlievee

    Charlievee New Member

    Joined:
    Dec 20, 2018
    Member:
    #8149
    Messages:
    1,287
    Try and find a local club and see what they are running. Hell, you can probably find 30 or 40 at your mall parking lot.
     
  15. Jan 11, 2020 at 9:46 AM
    #15
    glwood54

    glwood54 Stop making me buy stuff!

    Joined:
    Aug 19, 2019
    Member:
    #10964
    Messages:
    5,536
    Gender:
    Male
    First Name:
    Gary
    Albuquerque, NM
    Vehicle:
    2019 OR, KDSS, RSG sliders, Eibach shocks, 265/70 Falken Wildpeaks
    Nothing wrong with lifting for looks.
     
  16. Jan 11, 2020 at 4:14 PM
    #16
    Oldtoyotaguy

    Oldtoyotaguy Paid cash for it

    Joined:
    Sep 21, 2018
    Member:
    #7224
    Messages:
    1,599
    Gender:
    Male
    Vehicle:
    2018 Toyota 4 Runner Offroad
    Are you saying your 4 Runner isn’t 4x4? I didn’t know they made a 2WD 4 Runner. Anyway, good advice about doing some research, measure twice, cut once. I have a stock ORP, and I use it off road without any issues where I go with it, up here in the wilds of Canada. But, I get it, lifts look cool, I had one on my last Tacoma. I’ve looked at them for my 4 Runner and I’ve been attracted to ELKA, but I haven’t made a decision yet. It’s a Cadillac, and may be too expensive for some, but maintaining the integrity and driveability of the original is really important for me. Sure, it’s nice to hit the trails, but I also drive at high speeds on big roads and I’m not willing to sacrifice any of that high speed performance.
     
    Wvmoonshiner, Thatbassguy and Matze like this.
  17. Jan 12, 2020 at 4:44 PM
    #17
    WallyT4R

    WallyT4R New Member

    Joined:
    Aug 7, 2018
    Member:
    #6644
    Messages:
    2,443
    Welcome! :thumbsup:
     
    Dakotawright[OP] and Thatbassguy like this.
  18. Jan 12, 2020 at 5:00 PM
    #18
    Thatbassguy

    Thatbassguy New member? Really??

    Joined:
    Mar 27, 2019
    Member:
    #9314
    Messages:
    12,412
    Gender:
    Male
    First Name:
    James
    S/E Wisconsin
    Vehicle:
    2019 TRDORP, KDSS, MGM
    RSG sliders, Yakima offgrid basket, Pro-Comp wheels, SOS Streamline bumper and skids, Warn VR EVO10S winch + Ultimate Sidewinder, Bilstein 6112 + 5100 + rear lift coils, Rigid Dually SS ditch lights w/Caliraised brackets and OEM style dash switch
    @Dakotawright , welcome to the forum!

    There's lots of great information here already.

    As mentioned, many happy customers using the Eibach kit. Bilstein 5100's are another good budget option.

    Congratulations on your purchase! Post pictures of your progress.
     
    Dakotawright[OP] likes this.
  19. Jan 12, 2020 at 7:37 PM
    #19
    Daytonaviolet

    Daytonaviolet TRD Bro

    Joined:
    Mar 13, 2019
    Member:
    #9167
    Messages:
    1,639
    Gender:
    Male
    Bay Area, CA
    Vehicle:
    Blizzard Pearl TRD Bro
    Welcome to forums. Just read the threads which interest you such as lifts, wheels, tires and when your ready.. start modding. Personally unless you building for wheeling and crawling, a lifted 4x2 is fine. Many guys here have 4x2.
     
    SlvrSlug and Dakotawright[OP] like this.
  20. Jan 22, 2020 at 4:05 AM
    #20
    Dakotawright

    Dakotawright [OP] New Member

    Joined:
    Jan 11, 2020
    Member:
    #12661
    Messages:
    15
    Gender:
    Male
    First Name:
    Dakota
    Vehicle:
    5th Gen. SR5
    Thanks for the positivity. Not everyone (in real life, too) has been kind to me buying a 4x2 and wanting to make it more aggressive.
     
    Daytonaviolet[QUOTED] likes this.
  21. Jan 23, 2020 at 7:55 PM
    #21
    Volt656

    Volt656 New Member

    Joined:
    Jan 23, 2020
    Member:
    #12853
    Messages:
    3
    Gender:
    Male
    Vehicle:
    2020 4Runner ORP
    Do your thing man. Those people have their own issues.

    Anyway, from my research you could probably just use spacers without spending the extra money on suspension. I'm new to it too though.
     

Products Discussed in

To Top